Search results

  1. O

    32 peddle arm alignment

    Should peddle arm be heated in bending to make inch adjustments . Or can they be bent while in the chassis without heating. Having trouble installing wood toe board and peddle arms are not lining up with slots in the rubber bumper plate or the rubber bumper stops.
  2. O

    Weatherhead 1512 & oil filter

    Located a Weatherhead 1512 fitting with the small restricter hole to use on my oil filter. What size tubing and fittings are used with the 1512? From the female end of fitting it looks like it requires a Ford fitting(feral & nut), but the line indentation in the fitting looks smaller than the...
  3. O

    32 Vintique Fuel Tank question

    Has anyone had problems with sending unit in Vintique fuel tank not allowing body to fully rest on frame rails? if so, any suggestions
  4. O

    32 rear window metal channel

    I need two of the rear window channels that hold the vertical window runs in a 32 5-window coupe. The picture below is what I need two of, I understand these are approximately 4 inches long and attach to the wood of the rear window structure,
  5. O

    32 5-window rear window questions

    Had the package tray and window mechanism apart for several years for repairs and paint. Does the two wood vertical stanchions have two sheet metal channels that holds the window runs in place? It seems mine did when disassembled but have lost. If there is supposed to be a metal channel for...
  6. O

    1932 crossover harness for right taillight

    On a 32, how is the crossover wiring harness routed for the right hand taillight? Does it run across the front of the gas tank or the rear lip of tank?
  7. O

    1932 grill shell stainless trim

    How tight do you tighten the two threaded rods that come off each leg of the stainless trim on the radiator grill shell? I want to pull trim down tight to the grill shell but don't want to break the threaded rods by over tightening My trim has a small hole at the center of the horseshoe loop...
  8. O

    59AB in 32-Chatter rods

    Have stock 32 front mounts on 59 AB. In using 32 v-8 chatter rods with this engine, do you tighten the nut snug or do you tighten it til there is not space between rod shoulder and block? Or, should I shim the shoulder some with washers? I did tighten it up so shoulder of rod is touching block...
  9. O

    U-joint Cup-small hole

    In assembling the u-joint cup, does the side of the cup with the small hole go down or up?
  10. O

    Roll Pin/Spring Pin

    Is there a guide to use when using roll pins(Ace calls them Spring Pins) in determining undersize hole to be drilled. Example: I have a 1/8 inch roll pin, what diameter should hole be drilled to insure good tension on the pin?
  11. O

    32 accelerator pedal return spring

    Who sells 32 accelerator pedal return spring? Some catalogs list 35-48 and the copy of Mac's I have lists a 32-48. Been told that this will not work on my 32. Is there a source for this spring? Thanks
  12. O

    40 Lincoln Hubcaps-letter colors

    After polishing my 40 Lincoln hubcaps, I want to paint the "Lincoln" and "V-12" letters. What color of red was used for "Lincoln" and were the "lines and V-12" painted black or are they red too? Thanks
  13. O

    32 firewall insulator panel-revisited

    What is the best firewall insulator panel for a 32 currently, as to fit, appearance etc ? Is the fiberglass or abs the better choice. Wondering if something new and better was on the market now as I am to that part of my project? Thanks
  14. O

    32 drive shaft

    How do you disconnect the drive shaft from a 32 pinion gear, or is the drive shaft and pinion one unit? Does not have the coupler like my 38
  15. O

    Banjo Question

    The wheels on a 32 rearend I bought will turn in opposite directions when turned by hand. With both wheels on the ground it is locked up, even pulling the assembly by the torque tube(not in car) the tires skid instead of turning. Thia assembly has been sitting in a barn for a long time. Any...
  16. O

    2-bolt distributor to three bolt cover

    Just got my 59ab back from machine shop, They put a three bolt cover on the engine(I had taken him two 59ab to build one, one had the three bolt cover with adapter and the other engine had the two bolt cover). So I'm using the adapter on the three bolt cover. At the time I did not notice the...
  17. O

    32 Radiator Replacement Options

    My original 32 v-8 radiator needs to be replaced according to radiator shop. Engine is a 59ab. There are some leaks in radiator that don't warrant fixing according to rad shop.Not really willing to quote a recore charge for it. So, need to find a replacement. I'm familiar with Walker...
  18. O

    Zenith Model float valve

    Currently, who sells the best float valve for a Zenith on my 32 Model B? The one I'm using. has been damaged by the ethenol blend gas and it constantly sticks. Thanks
  19. O

    32 Model B Zenith question

    How do you disconnect the choke cable from a 32 zineth carburetor? Need to check on float setting and can't figure out how to disconnect the cable
  20. O

    32 Shocks-Test?

    How do you determine if a shock is working properly before installing. It is not locked up, it does have resistance and is not leaking.
Back
Top