Search results

If I were to hypothetically repaint my license plates, where would I get a yellow that is similar to the one used on the letters? And what product do you recommend?

My 352 was rebuilt and now i am mating it in my garage to the rebuilt cruisomatic. I made triple sure my torque converter was on all sets of splines and the trans slid right up with no gap so an unset tc shouldn't be the problem. My issue is that I can spin the engine only about to halfway...

I rebuilt my power steering pump but unfortunately didn't pay attention to which way the big gear in the center went. It is slightly curved to one side (seems to push fluid better like a paddle) so my thinking id that the curved side (not the rounded side) would go so that it works when the...

I am looking to do a swap on a future ranchero project from an original 289 to a 351w with cleveland heads. I am wondering if the mounts will be similar enough to bolt up the new mounts to the og. spots and drop in the 351. Has anyone on here done the swap? Any clearance issues in the...

My first car was a beat up daily driver 1960 Ranchero with a 144 i6 and a three on the tree with finicky linkage (weren't they all). I fell in love with the early 60's body style and want to do a more high performance Ranchero in the near future. I remember that the rear suspension barely...

I am rebuilding the rear drums on my 1963 galaxie. My question is about the return spring setup. Most of the pictures I see online shoe a return spring hooked to a bracket and from there a cable goes to the post at the top. Now, when i took mine apart, this was not the setup. Both side were the...

I have a 352 fe in my 1963 galaxie. All info i find says that the water pumps came in two versions only. A high flow and standard. For aftermarket they seem to all be high flow but I am finding an issue with the year. All info I find on fe blocks say that they ran from 58 to the 70's. But when I...

I've triple checked all the fender bolts are out, the bumper brackets aren't in the way, nothing is holding onto it but I cant get them to come off. They are wiggling all around but won't come off. Don't tell me you have to take the doors off or something. Help!

I'm mid restore on my 1963 Galaxie 2 door sedan and am getting about ready to reassemble the front fenders and core support. The core support and inner fenders had the typical surface rust that got to the original bolts too. I need these bolts to look factory original. I have asked around and...

did the upper arms change from 1960 to 1962? or is it just the lowers? thanks

I have a 1960 ranchero, need a passenger fender, wondering what years are the same. Is it just 60 and 61? or 62 and 63 as well? thanks for any info

my right front spindle is trashed due to a loose axle nut. The inner bearing welded itself to it and i would rather not spend a fortune in machine work. There are many spindles in my area but not from a 1960, but rather 63's and 64's. Does anyone know if ford changed the spindle design through...

need to replace the front body bushings on my galaxie resto. All but the four front bushings look show room quality and was wondering if anyone knew where to find them. I'd like to not drop 70 bucks on a whole kit when only four are needed. Anyone know of a place where general sizes are sold...

My 60 ranchero that i just picked up has some taillight issues. I haven't jumped into it yet but wondering if there are any prior suggestions or people who have had similar problems. The right blinker works and shows the right blinker is on on the dash( if that makes any sense) But the left...

I am new to the early Fords and have a Hotwell Health Heater. I am wondering if I could get any info on it. I found it in my 29 roadster when I bought it. I would like to know anything about it! Is it rare? Is it special? Is it worth anything? I have pics but am not sure how to post them from my...