Search results

I bought this Drake trunk gasket for my '37 Slantback, but not sure which way is up. This may not be like the original, I've never seen an original, but I assume this would work. Which way should it go? Thanks, Bill

Can someone tell me if the low profile bolts that bolt the front fenders to the inner fender are 5/16" or 1/4"? Thanks, Bill

Can someone tell me what was used in these metal cups that go over the trunk hinge bolts inside the car. When I removed them originally, they seemed to be full of something like old plumber's putty. Was that to keep water from leaking into the trunk? What's the proper material to use on...

Just curious where the original drain hoses from the corners of the windshield drained through the body? I'm going to take mine down the door post and though the bottom of the body unless someone can tell me where they should drain. I always like to follow the original intent if possible...

Does anyone have a Bob Drake windshield seal for a '37 Ford that can give me the dimensions of the leg that pushes into the windshield frame? The length I'm looking for is the the leg with the hook on it, between the tip of the hook and the rubber seal that pushes up against the frame. I have a...

I'm about ready to install the glass in my '37 Ford two piece windshield frame. I considered setting it completely in urethane, but worried that if I ever have to replace the glass, I may not be able to get it out without destroying the frame. I could use bedding tape, but to install the...

Looking for either one or both '37 Ford windshield joint clips. I've lost one of mine. Thanks, Bill Campbell

[FONT="Comic Sans MS"]I'm about to install the windows in my '37 Tudor and will be ordering window felt kits for the doors and rear side windows. In the kits I've seen, they appear to include felts that attach to the door itself, felts that attach to the window mouldings and channels that go...

I'm looking for the screws that hold the door latch assembly into the door. These are the ones that hold the latch to the door edge. They are something like 10-28, I have 10-32 but that's too fine and the factory screws have a slightly oval head and are countersunk. I've tried Bob Drake, Macs...

Does anyone have a picture of an open glove box door on a '37 glove box? My door is a nice clean original door and hinge and opens freely, but doesn't open up to a level position. It is still tilted up some and I don't want to force the hinge if it isn't intended to open any further. The...

How far should a '37 glove box door open? Mine doesn't open until level, it's more like 70 degrees or so. Its an original door and the hinge and all look in good clean condition. Thanks, Bill

Can anyone save me a few hours of head scratching and tell me where this loose spring came from? This is from the driver's door latch from a '33 Ford. I believe it has something to do with the handle position between opening and locking, but can't just quite figure it out. Thanks in advance...

Did the original '37's have a rubber weatherstrip between the deck lid and the body? Most restored cars I see have it, but can't tell from original photos whether there was one or not. Thanks, Bill

Wanted: '37 Ford glove box lock. Thanks, Bill

Wanted - 1937 Ford V-60 grille emblem in excellent condition. Thanks, Bill

Can anyone tell me what this semi circular recess in the beading on the driver's side of the firewall was for in an original '37? I've never seen a car with anything mounted there. Thanks, Bill

Wanted - NOS or excellent original V-60 (not V-85 thanks) grille emblem for '37 Ford. Thanks, Bill

So what's the secret in changing the latch bolt return spring on a '37 Ford door latch. I opened up the holder and removed the spring, but I'll be damned if I can wind up the new one tight enough to get it back in. Am I missing some secret trick here? Thanks, Bill

Why are there so many ads in the classifieds here that don't have pictures, while just about every other site has pictures with all the ads? Just curious......I know I can ask for photos of what I'm interested in, but the pictures would get me serious without having to ask.

Looking for an original '37 Ford horn in good physical condition. Working condition not important. Thanks, Bill