Search results

1955 crown victoria needs restored i have all the new patch panels this car needs as well as windshield and numerous extra parts engines transmissions etc. This car has all the options PS PB POWER WINDOWS AND SEATS this car is complete floor not rusted out. I will consider reasonable...

Looking for 26-27 rear fenders to fit touring,sedan 2dr or 4dr especially the right rear. pm me

Are there any model a driving tours in the midwest in 2017 I can not make the nebraska regional i am thinking september october may be three day events with a model a club in kansas, oklahoma, missouri or texas. Do not know where else to look for information.

I looked at the itinerary for the gettysburg tour coming up maybe i am wrong but it seems that folks do not do a lot of driving of their cars on these tours and that it is pretty much about seminars and judging. I have never been to a model a tour and all of the model t tours i have been on...

Looking for a winch to load my model a with trailer bed is 1 1/2 foot off of the ground ramps are six foot long car weight is 2400 how much winch to load this car will also use a ****** block.

Having just redone my model a steer box rebuit tight no binding shortened pittman arm synthetic grease teflon cups on drag link and and tie rod all ball are round and not worn. I have the car up on jack stands it seems a little stiff maybe because everything is new and snug but car turns from...

I have some photos to show here i have them in photobucket as well, i tried to load them here but am unable to do so i get a message about a security token i have tried to put these in a message i also have them on my computer can any body help i have uploaded some in the past into my album.

My car came with a trunk on the back you can see it in my avatar, I know the new ones the advertisers sell are wood and leather covered. Mine is all metal covered with a naugahyde or maybe leather not sure has leather straps and handles. the rack it sits on is stamped steel it is hinged so it...

I have an upper plate with the original style points but the face of the points do not match up, am i missing something here or are there different quality of points available some have talked about points from napa.

I have had this car up and running, with old style points and condenser but the points line up so terrible i put new points in modern upper plate wireless bottom plate made sure bottom plate was not grounding out to distributor body also checked upper point plate to make sure it was not...

Took my 30 tudoor out for a drive today about 8 miles runs just fine no oil leaks or water leaks ran bout 170 degrees. Brakes will lock up, transmission is smooth no growling shifts fine. Steering seems a bit stiff but then everything is rebuilt runs straight no wandering at all. Will finish...

Just got my 30 tudor started today went thru everything engine sounds real good had a scratching noise turned out to be a bracket no big deal barely turns over before firing right up. I have gone thru this car from front to back new brakes and drums. New seals in the rear end, new wiring put...

I am putting a new distributor in my car and i have it 12v neg ground the dist has the modern lower plate and new upper plate with points and condenser in it, i am asking if my wiring is correct. Battery pos to ign switch ign switch to + side of 12 v coil - side of coil to points.

If the moderators posted a link at the top of the forum for tours coming up in 2017 local,regional and national I know I would be interested is this doable or would other folks here be interested in something like that. Of course this would be up to the moderators but i was thinking of...

I did a search on the problem my new anti rattler springs do not put enough tension on the brake rods so i will fix that I will still add a helper spring just for a little added insurance. Last weekend I got my headlights all hooked up properly all wiring done, I added a six pole toggle for my...

I have a new motor in my model A it has a police head b cam zenith carb power balanced fsi ignition insert rods and bearings hardened seats(exhaust) and valves and adjustable lifters. That said i can get get mid-grade gasoline 89 octane no ethanol.I know alot of people add marvel mystery oil...

I have my steering gear back together and put the column back on steering wheel tightened it up good put the horn rod bushing in the steering shaft and then put the horn rod in the bushing fits tight on the horn rod, should it or should it be free or should it be tight in the steering shaft when...

Has anybody heard anymore just curious what did he find?

Looking at the worm gear on my 30 tudor to replace i assume it will go on either way or is it directional?