Search results

Great Condition

There is a rubber tube on the sheath of the Front Emergency Brake Cable about 4" long? Where is this supposed to 'Ride' against? Would it be between the exterior firewall at the, near the entrance site to the interior Emergency Brake Handle end? My cable frayed at the interior wheel... froze...

jwawhite@gmail.com In VGC Will pay for shipping in the USA

Hi, how does one install the metal wire ribbed bellow between the Heater Fan and Shroud at heater core? It seems I can't get the bellow over the male square perfectly.....one side yes then the other??

Seems my Speedo Cable rested up against a Header Exhaust Pipe of my Resto Mod. Anyone know of the correct routing and locations of the hold down clamps??

Does anyone have any experience with the Heater/Air/Defrost Control? B6A 18549-D The Plenum over the hump is missing..I believe removed for the under dash AC unit. The three cables are still attached to the unit, but one is detached, I think it attached to the vacuum solenoid still mounted on...

Something doesn't add up. The Dome Light (DL) is Grounded so when the DL switch is moved to the On position, the light comes on. A hot wire comes from the Head Lamp Switch for power. OK The Plasticized Diagram also reads: A Second wire from the DL is mounted before the switch so it's always...

Yes, even the original location has been moved. Does anyone know the correct location? Is it at the edge of the door opening or a quarter plus inch in? There are side by side holes on my floor….unbelievable but true. Would someone please take a look at their Driver, Passenger location and...

My car was rewired with modern day wires, all the cloth wires and connection blocks are gone. Wiring up the Door Buttons for the Dome Light, they have the Ford Female connection. What do you use to connect with the Door Buttons …or other areas?

Found out about this today, my dash is apart. I do have a nice socket bulb and rubber but where is the connection on the Light Switch for power? Needs to be on when parking and headlights are on? Which pole on the Switch/ Anybody got a clue?

Gauges not working, Pulled Pod, PITA. Pod has stickers on revealing it was worked on by a Speedo Shop, a long time ago. Called the shop and asked about the reducer 12-6 V mounted between the two gauges. He states the gauges are 6 volt and if hooked to 12 V will fry 'em. Looking at the...

Anyone out there, how did you remove the upper Pod Nut? The ones next to the turn indicators? I cannot get a box on them for the Dash backing plate is almost up against the studs. Words of encouragement taken gladly.

Serpentine Belt? What the… Calling on Meccanixs out there. Installed SERP belt quiet for 15 miles? Parked car came back later belt now squeals. It becomes quiet step on the gas starts to squeal. Water trick still squeals. Stethoscope on all pulley operated items except Damper. No noise...

Serviceable Parts for Control Valve

As you see it.

Minus Worm Gear and Shaft, Sector Shaft bearings feel stiff, needle bearings are all installed. Will of course need new seal.

All of these items off or for a 1956 Ford but as you know some of them fit other years also, Old Henry didn't want to waste a part! Pitman Arm, Gear Lever, Harness Holder (lower), Springs and Caps for Auto **** lever tube, Horn Spring, Steering Box Bolts, Upper Steering Shaft Centering Bushing...

50? Miles on Unit. It's a '56 Steering Tube with the cut Rod and u-joint. The '56 Tube/Shaft is shorter bc of the deep dish Steering Wheel 805 3960414

Help Need Photos of Power Steering Lines ‘56 I have a restomod 56 Wagon with a 302. My pressure line cannot take the stress of movement at the Control Valve. It’s busted again! Would someone please send photos of the lines from the frame mount to the control valve? I’d like to see the...

Anyone have any questions about the Borgeson Unit that I removed from my 56 Ford?