Search results

Hello ! Does anyone know the overall dimminsions of a 40 ford deluxe coupe radiator. I know that there close to 25x21 This would be a all stock replacement All the ones i've looked at are all different sizes ? So i'd like to choose the one thats closes to original any info thx CR.

1940 Ford Tudor Sedan Body not beat. Frame - No rust outs straight & true Engine - 221cid, all ways starts, runs real smooth,drives with no effort. Color - Cloud Mist Gray in suede. Interior - needs a head-liner Over all this car is tidy Drive as is - Restore -Hot Rod For more info email...

1940 Ford Standard Tudor Sedan Primarily - all stock original car Paint Color - Cloud Mist Gray in suede Lots of New parts CID - 221 If serious only email for more info - crowe67@outlook.com

Hello ! Q: Can you use a 1940 Ford truck frame for a 1940 Ford sedan body ? I know the frames are the same, what I am concerned about is the body to frame hole locations. I know the truck frame needs the 4 outer-frame body mounts 2 on each side, but did Ford drill all the holes to except all...

Q: Stock 50 merc standard coupe, 3 spd.(no overdrive) What rear end ratio would have come stock from the factory ? or could you order it ? CR.

On a 50 Merc, is the top end of the spring where it sits in the cup, is the coil round, flattened, or half round ?

Doing some repair work on a 40 sedan frame. Frame is bare no body (just frame) If I remove the center box / section on the X member , will the frame pop in other words is the frame under a load ? I need to replace this box and repair rust. Will I have problem with rivet hole alignment for new...

Hello ! I have an old Sun Tach. one of the first with no sending unit needed, I have four wires comming out of the back. red white blue black Does anyone know the color code ?

I would like to know how you can remove the ignition switch from the dash of a 50 Merc. Any help would be great !( i do not want to scatch the dash) CR.

So my steering box has just been rebuilt and is ready for install, what is best, pack full of grease or fill with heavy oil. Any opinions. CR.

How do you delete a thread ? I had some items for sale that sold, now I would like to delete the ad. I was looking for a delete thread option but can'nt find how to go about it. Can someone tell me how ? CR.

Hello ! I am looking for a 1940 Ford sedan gear shift lever (as mine is bent and pitted ) If anyone has one they would like to sell I would be interested. My name is Chris, located in Denver contact me: acmefive@hotmail.com Best CR.

If this want ad is up, I am still looking for a lever. Never heard back from Crestliner ^ ? CR.

For Sale 55 Ford front turn signal housing for drivers side very clean no dents, pits, --- $50.00 (SOLD) 55 Ford front turn signal lenses with socket assembly---$50.00 55 Ford tail light housings pair (reproduction new)---$50.00 pr. Contact Chris: use this email acmefive@hotmail.com

Hi ! I am looking for colunm gear shift lever for a 1940 Ford sedan. ( the shifting lever itself) If anyone has one or knows where to locate one I would be interested. Best, Chris Rowe acmefive@hotmail.com

Thank You Guys ! CR.

Thanks Kube ! I will give it a go, being mindfull of the rubber which I hope might also be replacable. CR.

Hi ! Can someone let me know the best way to remove the shift lever. (someone has bent my lever towards the steering wheel,why ?) I see there are nubs on the end near to where lever conects to shifting rod, are these spring loaded or is it a roll pin ? CR

Hi Men ! Q: What would be the most simplistic way to remove the steeringbox/column from a 1940 Ford sedan? (wantingto remove box for rebuild) CR.

Hello ! I have seen a few hotrod 40s with 1942 split wishbones. Is there a benefit to using 1942 wishbones vs. 1940 wishbones ? I can see the angle in the 42 vs. the 40s, but do not know how this helps ? Any feed back would be nice as I have a hotrod 40 and have both styles of wishbones and...