Search results

  1. Z

    38-39 Ford flathead taillights teardrop

    38-39 Ford flathead taillights teardrop lens.2 lens are NOS 2 are chiped spares in usable condition. Bucket are solid.
  2. Z

    WTB- New/NOS flathead pistons 3-3/16 (STD)

    WTB- New/NOS 3-3/16 (STD) flathead pistons. Standard size only.
  3. Z

    21 stud flathead

    36 21 stud. I removed the head to repair a cross threaded plug hole, and found that the cylinders have rust damage. Its allready .80 over. What should I do with this motor?
  4. Z

    Banjo rear hub question

    This hub has two cut grooves at the top, am I missing a retaining ring?
  5. Z

    Reverse eye spring spreader + Flathead valve tool

    Reverse eye spring spreader $75+ shipping Flathead valve tool 35+ shipping
  6. Z

    Banjo rear question for the experts

    I have a '28 roadster on '32 frame with a '37 rear end. A while ago I broke my drive shaft and took the opportunity to rebuild the whole rear end correctly. I just found out my torque tube is warped from heat distortion from welding radius rod mount on, this probably caused the drive shaft...
  7. Z

    Torque tube isuse

    My shortened torque tube is binding up(42 rear/tube, 32 frame). Does shorting the torque tube change the geometry? Is my new center bearing misaligned? Or considering the torque tube is shortened should I not run a center bearing at all?
  8. Z

    Ford banjo rear question.

    I'm putting my banjo rear together again and the axles seem to be tight in the carter housing. they barely turn (opposite direction) by hand. is there a rule of thumb on how tight they should be? This a 37' rear, rebuilt with all NOS/New parts. 18 tooth axle, 12 tooth spider.
  9. Z

    Ford banjo rear end issue.

    I just rebuilt my 37' axle complete with NOS axles. the hubs are 42'. the hubs are tightened down and it looks like I have the wrong hubs or axle, what gives?
  10. Z

    32 Ford flathead V8 motor mount

    32 Ford flathead V8 motor mount kit. economy replacement for the rare and expensive stock 1932 Ford V8 motor mount. Laser cut from A36 structural steel, needs to be welded and braces added. $40 Shipped zgears@yahoo.com
  11. Z

    banjo rear axles with good threads

    I have 2 16 tooth banjo rear axles with good threads. 80 each Contact zgears@yahoo.com
  12. Z

    28-29 ford roadster stanction parts

    I need a model a ford roadster stanction inside liner(driver side). not seen but mine is very thin, and rusted out in the channel.
  13. Z

    1942 ford banjo rear.

    1942 ford banjo rear. The complete rear axle only. needs rebuild. zgears@yahoo.com 910-947-3773
  14. Z

    49-53 8ba ford flathead connecting rods

    I have 4 spare 49-53 8ba ford flathead connecting rods. $10 each also have a 8ba manual flywheel $50 zgears@yahoo.com or 910-947-3773
  15. Z

    48 1/2" rear passenger side radius rod 40 41 42

    I need a 48 1/2" long rear passenger side radius rod. I think my old one is a 1942, not sure on other years. Need undented, and preferably unrusted, or with out deep pits. zgears@yahoo.com
  16. Z

    Torque tube bearing removal

    Can anyone tell me the correct method for removing a center ball bearing plus neck race and seal from a 40's ford Torque tube?
  17. Z

    40 ford rear hub race?

    There's a pressed steel race(?) in the back of a banjo rear wheel hub. Is that available anywhere? Is there a part number for it?
  18. Z

    35-48 Ford Torque tube driveshaft

    35-48 Ford Torque tube driveshaft, 6 spline. prefer near by. Please send email, I don't check Ford barn that often. zgears@yahoo.com
  19. Z

    NOS bearings USA made

    I'm looking for some NOS roller bearings (FoMoCo or Timken, no new Chinese, thanks). For my ford banjo rear I'm rebuilding. If anyone has them or could point me to a dealer, it would be appreciated. 1935–47 Pinion races (double faced) 48–4616, Timken 27820D 1935–47 Pinion bearings (two needed)...
  20. Z

    Ford flathead Fenton 2x2

    32-48 Ford flathead Fenton 2x2 zgears@yahoo.com
Back
Top