Search results

Greetings, At some point, my grandfather installed a Fram (?) oil filter canister on his '34 Fordor deluxe. I have a number of filters, but the intake and exit hoses are suspiciously hard. Are there specific replacement hoses available, or does one just "find what fits best"? If specifically...

Original engine and radiator Engine head has "authorized recondition" sticker, paperwork says 1953 at 52k miles. Odometer reads 53,600 Replaced water pumps circa 1980 Pumps were regreased currently. Radiator removed and sent to shop for cleaning early 90s Car has been garaged and "DMV no-op"...

Greetings, I need to replace the anti-rattle felt and forward vertical channel in my 1934 Fordor Deluxe Sedan. Numerous calls to the regular parts houses come up empty for kits. The forward vertical channel seems easy enough to source. However I am having difficulty sourcing the the body window...

My 34 Fordor Deluxe has an elastic rope weaved grab "handle" on the back of front seat and similar material broken short handles attached to the rear C pillars right and left. What are they officially called and where might one seek to find a pair?

So, I've been purchasing parts over the years from Mac's. Invoice's come back "Mac's" Today I called regarding an interior question for '34 Ford Fordor Dlx...... Didn't get Mac's, so hung up and called again. Surprise surprise, right number, unexpected answering remark "Eckler's" How long has...

Did Grain-it Technologies (woodgraining) close? Their website "can't be reached."

I'm thinking of DYI all the woodgraining pieces of my '34 Fordor Deluxe. The pattern is Redwood Burl, Mahogany. For those of you that may have done this, what additional equipment/accessories are advised to have along with the Grain-It Technologies Basic Kit. Thanks in advance. Cheers!

Greetings, I'm trying to hook up an 12 inch red LED light strip similar to: http://www.ebay.com/itm/LED-Lighting-Strips-for-6V-12V-Self-Adhesive-Ultra-low-Temperature-/170882923791?pt=UK_Trains_Railway_Models&var=&hash=item27c96a7d0f I'm having a problem that I can't seem to figure out. When...

Greetings, I ask this not for my '34 Fordor but for my '65 BMW. I am installing an electric fuel pump (Carter 6V) in lieu of a mechanical pump. I was sold a Painless Fuel Pump Relay kit as well. However, the relay has "12v 30amps " printed on it and comes with a 12v 30 amp circuit breaker...

I have a DeVilbiss Startline Blue with 1.8 tip. I'm spraying PPG K36 Primer 5:1 on a clean sandblasted spare tire cover. The pressure coming out of the compressor is 85lbs. The pressure regulator at the base of the gun is set to 35lbs. The paint hits the metal and sets up like grains of 90...

I was quoted slightly over $4000 by Lebarron Bonney for a '34 Deluxe Fordor mohair interior kit. I recently received a 15% off Interior Kit coupon from Mac's. Mac's sale price for a '34 Deluxe Fordor Sedan mohair interior kit is under $2 grand. I was planning on installing myself.....never done...

Greetings, For the screw that attaches the gas line clip to the engine side of the cowl, is it one of the axle screws used to hold the inside cowl insulator panel, a flat head screw with a cup washer or a round head screw. I seem to have one extra of each....however, I'm pretty sure the round...

I have two dash lights. One light is mounted at the upper cowl and its wire is connected to the right side of the fuse block. The second light is mounted on the lower center of the dash, the wire goes to a switch mounted on the lower left of the dash. I have no other wire. Can any one confirm...

In the upper middle of the cowl of my "34 Fordor there is one hole at the midline and one hole higher and to each the left and right. I know that the left and right are for the choke and throttle rods, but what goes through the center hole? I have the coil generator wire, the cowl harness and...

I'm going to put in new interior into my '34 Fordor soon. Does Acostishield insulation make that big of a difference? Anybody use/install it? Is it as easy as Mac and LB say it is to install? Cheers!

I had my original windshield frame rechromed by Walker's Custom Chrome. The new glass came from Mac's, as did the bedding material. The original "L" shaped frame corner braces were rotted and aftermarket replacements could not be found, so I fabricated new ones from 5/16th square metal rods...