Search results

WTB the updated steering linkage made by Fatman for a 1951 Ford.

WTB the updated steering linkage made by Fatman for a 1951 Ford.

Hi everyone, I recently replaced the heater core in my 1951 Ford Victoria. The green bible says my engine should accommodate 5 gallons of coolant, yet I was only able to fill it with just shy of 4 gallons. The heater control valve is functioning, and the thermostats didn’t show signs of...

Hey everyone, I was hoping someone could advise me on coil spring options for a 1951 Ford Victoria. I am aware that Aerostar springs bolt in, and I'm interested in the improved ride quality achieved from progressive coils, but I am looking for stock ride height. Anyone know of any similar...

Hi Everyone, Just got back from Hershey and am in full Ford mode! Finally pulled the engine out of a project '52 Ford Victoria (anyone interested in a rolling chassis?) with the intent to rebuild it for a '51 Ford Victoria. I know Walt DuPont is the authority on Flatties but I'm not sure if...

Hey Everyone, Just wondering if anyone has any experience with running a cool carb heat shield on a flathead? Thanks!

Hi All, My father and I rebuilt a 1951 Ford Victoria steering box this weekend. Upon completion, the steering wheel feels tight to turn in the center of the turning range (when turned to favor either side, it becomes easy again). We adjusted the sector shaft to the best of our ability while...

Hi All, Just bought a new clutch release bearing from shoebox-central. There is play between the bearing and the hub, and there is audible grinding when spinning the bearing. Just wondering if this is normal? Thanks, Justin

Hi All, Currently rebuilding a '51 Ford victoria steering box and I've run into an interesting difference in parts. I have two sector shafts to potentially be installed, one has needle bearings and the other has bushings. The bushings seem to fit much more tightly. Any recommendations on which...

Hi Everyone, I replaced the bullets in my grille today with some clear road lamps to help night driving (and for the cool factor!). They look and work great, but I'm worried about the load it will be putting on my stock electric setup. Does anyone know where I can source parts for the heavier...

Hoping someone can explain to me the difference between coil springs that are identified as either Low Limit Springs or High limit Springs, as described in attached Ford literature excerpt. Also wondering if Victoria should utilize standard springs vs convertible springs. Thank you.

Hi Everyone, When I depress the clutch pedal on my '51 Ford Victoria, I hear a pitter-patter directly related to the the RPM of the engine. Does anyone have any idea what this could be? Thanks!

Hey Everyone, I've got a '51 Ford Victoria experiencing charging system issues. Can anyone recommend an auto-electric shop in the Massachusetts MetroWest area? Thanks for the help.

Can anyone identify the correct fuse for the Colonial 1CF 1951 ford radio? Thank you!!

I purchased new glass for my 1951 ford victoria and tried to replace the passenger window today. It was going smoothly until I attempted to put the new window into the window frame. I wrapped the rubber seal/gasket around the window and tried to slide it into the frame, but it wouldn't seat...

Does anyone have a 1951 ford (preferably with overdrive) in the metrowest/Boston area I could look at? I have no pictures and I need to see the shifter linkage connections badly. I'll travel to wherever the car is to take a look, i've run out of solutions :( :confused:.

I have a 1951 Ford Victoria that was not delivered with factory overdrive. I know this because there are two less than perfect holes under the gas pedal for the kickdown switch. To date, the lower hole has been used. However, the rods that were in place were clearly homemade and one was...

Does anyone have pictures of their setup? I purchased the new driver-side manifold that has the exhaust port pointed towards the rear, but I do not have the correct pipe to link to it. I could potentially make my own pipe, but I also do not know where it goes. Does the exhaust pipe go above or...

Does anyone know if anyone sells dual exhaust manifolds for a 1951 ford flathead v8? I am specifically looking for a manifold and not headers. Does pat Rooney still make them? Does anyone know how to contact him? I am in a time crunch so replies are greatly appreciated!!

Anyone have any experience with the new edelbrock 94's or Dennis Carpenters new carbs? I searched but I could only find information leading up to both of their releases, no actual review. What's the verdict? are they any better than a rebuilt holley 94?