Search results

Have a 1930 town Sedan that I purchased in 2000. At that time I pulled the original engine out and had it redone including balancing, counter balanced crank, hardened valve seats, lightened flywheel, etc. This rebuilt engine had been stored in my garage since 2000 and was routinely turned over...

Found this old tool in a box while clearing out a basement. Any idea what this tool was designed for? It is cast and 6" long. Has a square opening that would fit a 7/16" square nut or shaft

Anyone know of a source for a 30/31 coupe header drawing?

Decided to rebuild a Zenith carb today and had difficulty in separating the upper and lower bodies. Finally got them apart but broke the venturi in the process and now have a piece in the upper and a piece in the lower body. Any suggestions on getting the pieces out? Did some tapping but...

I am posting this for a friend. Three KRW combination machines with various Model A & Model T accessories. One @ $3,500, one @ $2,500 and one @ $2,000. For detailed info on the machines and accessories contact Butch Nichols at 410-335-7163.

I am posting this for a friend. Three KRW combination machines with various Model A & Model T accessories. One @ $3,500, one @ $2,500 and one @ $2,000. For detailed info on the machines and accessories contact Butch Nichols at 410-335-7163.

I am posting this for a friend. Three KRW combination machines with various Model A & Model T accessories. One @ $3,500, one @ $2,500 and one @ $2,000. For detailed info on the machines and accessories contact Butch Nichols at 410-335-7163.

Anyone have or know where I can find a detailed drawing of the belt rail? I am having trouble fitting my rail over the gas tank. The outer ends of the curved portion that fits down onto the tank touch the tank and I still have a 1" clearance in the center portion . Too much to try to draw...

Bought a 30 OCPU project about 8 years ago and have finally started to get it together. When purchased most items were there and some assembly had taken place with body parts in primer. Turned out everything had to be redone even the frame had to be stripped and repainted. Turns out that the...

Can some one describe the bolt that attaches the wood slat that runs up from the seat riser to the back of the cab at the cab body end. This is the wood slat that the backrest rests against. The bolt in question comes thru the cab body near the top side and has a mushroom head.

Have a new windshield frame and want to drill the appropriate holes before I have the glass installed. Looking for the hole locations for the wiper and the top snaps. Is there a drawing that will give the dimensions? If not could someone measure them for me? Appreciate any help. Project...

I have a reprint of the "1931- 1932 Catalog of K.R. Wilson tools for Ford". In that catalog they show the machine and attachments for both the Model A engine and the Model T engine. To update earlier Combination Machines to the Model A engine they list 12 attachments required for this update...

Sold

Offering a 25 watt resistor for use as a means of droppng a 12 volt input to operate a 6 volt Model A Ahooga horn. The resistor can be housed within the horn cover or added to the wiring in the engine compartment. When mounted inside the horn one input wire is pulled from the horn contact...

The exploded view of the powerhouse generator shows two cork gaskets, one on each end of the main shaft. I don't recall seeing such gaskets when I disassembled the unit. Are they necessary and if so what would the thickness be? Have not seen any being offered in the parts catalogs so assume I...

Need to know where to find detailed info on the wood pieces that go behind the seat back in a 1930 Roadster PU. I have the 3 pieces that run up from the riser and the two pieces that go behind the back side of the door opening. My question is what do the three upright strips attach to at the...

Where can I find a detailed exploded view of the 5 brush Powerhouse generator? Thanks in advance for any help on this.

30/31 AA radiator. I had this radiator professionally flushed and rodded a few years ago. Didn't realize it was an AA radiator until I attempted to put the A shell over it and found out that it didn't fit. The 1/2" spacing from the front face to the fill neck makes it an AA radiator. When it...