Search results

i HAVE A 1937 v8 MOTOR IN MY MODEL a fORD, AND i NEED SOME NEW SPARK PLUGS. cAN ANYONE tell me what plugs I should be using.Thanks

Can anyone tell me what the recommended current (amps) should be running through a 6 volt ignition coil primary circuit in order to provide long life on ignition points on a model A ford. I can calculate the resistance just need the suggested amps

will a 1931 model A Ford manual transmission fit directly onto a 1932 model B Ford four cylinder motor without an adaptor ? Anything else I should be concerned with when trying to match these two up ?.

I have a very good model B 4 cylinder motor and syncro transmission that I would like to install in my 31 model A coupe. The model B set-up I have is a complete motor with transmission, however I notice there is no brake pedal assembly like there is on the model A set-up. Can any of you...

Is there any electrical difference between a 6 volt and a 12 volt ignition coil ? Also is it ok to use a 6 volt coil in a 12 volt system ? keeping in mid that I would be limiting the primary current to 3 or 4 amps by using an exterior resistor if needed. Can anyone recommend a 12 volt coil...

Here is a list of items I need to finish my 30/31 Leatherback Victoria 1. window frame for drivers door with or without square spacer molding Snyders # A-45985-L - window frame dimensions should be: top = 29-3/4", bottom = 31-1/2", one side = 13-3/8", other side = 13-13/16" 2. Quarter...

I have a 37 V-8 21 stud flathead with the crab distributor. Are there any conversions available on the market instead of using the crab ?

I am looking for a Ford 01A-18683 tube and clamp assembly for use with Ford oil and motor cleaner (Oil canister). this mounts from oil canister outlet to timing cover. I have the filter and canister. please email me at ogatrains@gmail.com since i do not check on the forum often. or leave message...

I want to install an oil filer on my 1937 early 21 stud V-8, the motor is installed in my resto-mod car and I do not have access to drill the block for a return piping connection. I do have access to the pipe threaded outlet area at rear of block which contains the .060 restrictor. There is no...

I am looking for the small version (oil canister) or container which fits onto v8 flathead with three bolts. I have a canister which has been modified to fit onto firewall but want to mount it back on the head. Please email me at ogatrains@gmail.com with your contact info The canister holds the...

I have started to install the new interior wood in my Victoria but looking at the side mounting holes that run along the body at the belt rail area and above windows area are much larger and the nails sold by the suppliers have heads that just barely hold as they are too small. I cant find any...

Here is a list of what I hope to pick up at Hershey for my 30/31 Model A Ford- if you have any of it please send me a private email to ogatrains@gmail.com - front fender bracket stamped metal type not cast - rear bumper for slant windshield preferred but will look at regular, must be rust free -...

Is the bell housing AND transmission painted Ford green same as the engine from the factory or was any of it painted black ?

I know the Cabriolet has a roll up window in the doors, does the window have a structural frame around it ? in other words when you roll down the window does it look exactly like a roadster or does the window frame stick out ? thanks

Years ago I purchased a Model A which had been converted to hydraulic brakes. Its time to replace or fix the master cylinder due to leaks and pressure build-up. I would like to install a dual cylinder master, or at least get a replacement, however, the fit up is quite different from what is...

I need to reverse position of tie rod on my spindle from top to bottom on a steering conversion job. The Ford spindle I am using will accept a tie rod from the top and I need to reverse it so that I can attach the tie rod the opposite way in order to clear the wishbone. in other words the taper...

I need pictures to see how the body installs onto the floor sill assembly. My early leatherback was in very rough shape, the side sills were non-existant as the wood rot had completely vanished and turned into paste. The rear of the body was sitting on the bumper brackets. I now have the floor...

here is a list of 1931 Model A Victoria parts I require. I will be at Hershey Tuesday til Friday AM. If you have any of these parts you can call my cell at 613-833-8331 or email me at ogatrains@gmail.com -rear floor pan -drivers door window frame -drivers door garnish molding spacer -drivers...

I'm working on an A-V8, converted it to hydraulic brakes using a Ford (I think 42-48) spindle set , put in a Vega steering box, both spindles connect well together with their tie rods, however when I tried to insert the tie rod end for the drag link the taper is reversed on spindle, meaning the...

I have my eye on a Flathead V-8 motor with 8RT markings - what can you tell me about the year and what were they installed in ? also HP ? Thanks