quickchange question

The rear axle needs to be removed, disassembled, reassembled, and set up. Also I think the QC housing input shaft is a different depth than the stock pinion and the driveline needs to be shortened slighty? Not entirely sure about that, the only one I've done needed the whole shaft shortened a LOT to fit a '32 frame.

Also, much more trouble than the axle itself, you'll need to change your rear crossmember/spring to a Model A or T unit and possibly modify/notch your fuel tank to make room for the longer QC housing.
 
I wouldn't think you would have to change the drive shaft length. What kind of quickiechange are you considering? Wayno
 
Elmo Rodge said:
I wouldn't think you would have to change the drive shaft length. What kind of quickiechange are you considering? Wayno
Click to expand...

I know there's a slight length difference, just not sure if you have to bother changing the TT and shaft length. Might be enough to goof up the speedo assy. Regardless, it would be a PITA to install!:D
 
The shaft and torque tube (if applicable) are relocated on the quick change housing so the short shaft can go under the ring. Sometimes even the spring hangers have to be addressed to get everything at the correct alignment. It's no small bolt in alteration for sure.

Kerby
 
The spider carrier also needs to be machined to clear the lower shaft, the pinion gear needs to be machined to fit into the rear cover bearing.
 
Human Fly said:
The spider carrier also needs to be machined to clear the lower shaft, the pinion gear needs to be machined to fit into the rear cover bearing.
Click to expand...

Good points if you're using an original old QC center. I think the new kits come "ready to install" with no machining required.
 
Jim in Upstate NY said:
How hard is it to change out a stock 37 thru 40 rearend center section to v8 quickchange. Both are closed drive. Thanks, Jim
Click to expand...

You mention '37 - '48 rear but what year/body style vehicle are you planning/thinking about putting a QC into? I'm putting a closed drive QC in a '35 tudor sedan. This is a Winters/Spadaro V8 unit. I did not have to cut or change the drive shaft or torque tube in any way. I did have to fabricate a new rear cross member by using the center section a Model A and both ends of a '35 cross member. Also, I had to use a Model A rear spring. While fabricating the rear cross member, I had to design in a slight angle change because the TT/drive shaft attaches to the banjo at a lower position and angle rather than in the center of the banjo as the stock rear did. I designed the new cross member such that it is not required to cut a rectangular hole in the rear floor pan and it does not interfere with a stock gas tank. This was a pretty easy installation because I am working with a bare frame that does not have the body in place yet, but as others have said this is not just a drop in and go project. You need to be determined that this is definitely what you want to do before starting but it is possible. There are three sources, that I am aware of, where you can purchase a new and complete closed drive QC center section. This is in addition to the possibility of finding an old original QC to use. I'll attach a couple pics of what I am building FYI. If you need any additional info on my project, let me know here or send me a PM. Good luck!
 

Attachments

  • 35RollingFrame-5.JPG
    35RollingFrame-5.JPG
    90.9 KB · Views: 165
  • 35RollingFrame-3.JPG
    35RollingFrame-3.JPG
    111.6 KB · Views: 153
  • 35RollingFrame-1.JPG
    35RollingFrame-1.JPG
    99.2 KB · Views: 142
  • 35RollingFrame-7.jpg
    35RollingFrame-7.jpg
    62.2 KB · Views: 131
  • QC-Rear-35Chassis-5.JPG
    QC-Rear-35Chassis-5.JPG
    87 KB · Views: 160
  • QC-Rear-35Chassis-2.JPG
    QC-Rear-35Chassis-2.JPG
    84.1 KB · Views: 149
  • QC-Rear-35Chassis-1.JPG
    QC-Rear-35Chassis-1.JPG
    91.7 KB · Views: 153
  • 352DrDelxHotRod-1.jpg
    352DrDelxHotRod-1.jpg
    67.1 KB · Views: 125
  • 352DrDelxHotRod-2.jpg
    352DrDelxHotRod-2.jpg
    71.8 KB · Views: 123
  • 352DrDelxHotRod-4.jpg
    352DrDelxHotRod-4.jpg
    68 KB · Views: 120
Last edited:
make sure you get a set of ear plugs.every one i ever rode in cryed like a spoiled brat in a toy store.may be the new ones are different i am sure the barn will chime in
 
richard crow said:
make sure you get a set of ear plugs.every one i ever rode in cryed like a spoiled brat in a toy store.may be the new ones are different i am sure the barn will chime in
Click to expand...

Crow, I'm not really concerned about how much those straight cut QC gears whine. As of 2-1/2 years ago, I lost most all of my hearing. I am now almost totally deaf. Even if I could hear well, the dual straight exhaust will make more noise than the QC gears. However, those who care to ride with me may need the ear plugs :).
 
I've got stereo. An old Halibrand V8 QC in the back, and a GMC 671 up front on the Flathead. No ear plugs!
 
Coupla things: reverse the axel housings and put the spring in front of the axel. buy a quite gear set.
 
Where are you guys finding these center sections at? I have a late 40's open drive rear, I would love to make into a QC. Nothing beats the look. Any websites with good info on putting one all together?
 
patdoody

You might find some info on the HAMB. You can also check out Dick Spadaro's or Hot Rod Works' web-sites. They have both done a lot of work getting quick change parts available to rodders with just about any part a person might need to get their particular car set up. There are others out there too, but I'm just more familiar with the two mentioned.

Kerby
 
I have ran Dick Spadaros unit in my GMC powered Model A for the last five years. Love it with no problems!! I used the Wilson welding 41 Lincoln brakes and a 46 ford rear.
Set up is pretty straight forward as well.
 
You must log in or register to reply here.
Back
Top