F150 ****** with overdrive

Gear Vendors makes all kinds of stuff. Generally, they make adapters so that an O/D can be added to some or all of the most popular transmissions (Std and automatics). I think they also now do an in-driveshaft O/D for Model A's and early V8 Fords.
Keep in mind that Gear Vendors owns all the stuff that was originally the Laycock-De-Normanville Overdrive (Volvo, Austin Healey, Triumph, etc.).
Jim
 
Here are a few pictures. The transmission is a Jeep Aluminum case, fitted with Ford gears (yes, they fit w/out modification). Then an adapter was made to connect the O/D to it.
The shifter top assy is also Jeep and I used a Marlin model 66 gun barrel to be able to run the wires from the shift ball. The ball is from a Volvo and has the switch in it to trigger a set of relays to engage the O/D
 

Attachments

  • chassis engine 002.jpg
    chassis engine 002.jpg
    120.7 KB · Views: 487
  • chassis engine 004.jpg
    chassis engine 004.jpg
    118.4 KB · Views: 396
  • chassis overdrive 001.jpg
    chassis overdrive 001.jpg
    142.3 KB · Views: 312
  • chassis overdrive 003.jpg
    chassis overdrive 003.jpg
    155.4 KB · Views: 287
Thank You
I've got about 750 miles on the car now. The O/D functions well. I'm running a 4.11 rear axle, and in O/D it equates to a 3.20
Jim
 
I appreciate the pictures and the information. I am going to have a wait for a while to do something. I kind of like Dave's the best right now.

Thanks Again
 
Model A adaptors 004.jpg

Model A adaptors 005.jpg

Model A adaptors 006.jpg
The photos show a bell housing adaptor made in New Zealand by Mac's Speed shop and sold in the States. (I don't know who by)
This alloy casting includes the shaft for the clutch forks and pedals left or right hand drive
It is a simple bolt-on job for the F150 gearbox, but because the input shaft spline starts further back than the Model A one, a special offset clutch plate has to be made.
In this installation, there is also a quick change rear end and consequently there is also an open prop shaft
 
That is a nice bellhousing, saw one at a swap meet the vendor had a price tag $395.00 did not notice is there a mount on the bottom for the wishbone?
 
Who is NOW building these transmissions and that are RELIABLE. Dave's Delhume site is down again. I can't get in contact with him.
 
I have a model a and want to keep it as stock as possible if I want race I would buy a lamborgini I am not trying to be cheeky but why a A if not to put around han have people admire my car stock?
 
spdway1 said:
Who is NOW building these transmissions and that are RELIABLE. Dave's Delmue's site is down again. I can't get in contact with him.
Click to expand...
I just went to his site and it came right up:
modelaonly.net

Contact info on his website:
Dave Delmue
17649 Peak Ave.
Morgan Hill, CA 95037
408-722-2518
Email: [dave4564@msn.com]
 
a-bone newby said:
I have a model a and want to keep it as stock as possible if I want race I would buy a lamborgini I am not trying to be cheeky but why a A if not to put around han have people admire my car stock?
Click to expand...

You can use your Model A to go apple picking and it is your car to do what ever you please. We use ours to race (nostalgia hill climbs and such). It is not a hot rod by any means. Just looking for a transmission that will do the job! Any suggestions?

Second place is the first looser!
 
spdway1 said:
You can use your Model A to go apple picking and it is your car to do what ever you please. We use ours to race (nostalgia hill climbs and such). It is not a hot rod by any means. Just looking for a transmission that will do the job! Any suggestions?

Second place is the first looser!
Click to expand...

You had me laughing spdway, that was good, (go apple picking)
 
You must log in or register to reply here.
Back
Top