Search results

Is anyone aware of any Flathead groups/clubs in the Sacramento, CA area? More so Roseville to Auburn area. Looking for help with the small things on my cars and would like to get some other opinions in person. Thanks

The rear transmission mount has one of the ears broken off. Has anyone had to replace JUST this piece without purchasing the entire kit?

Thanks! Should have known based on some of the other parts that it wouldnt have been a ford MC.

Pics attached now

Anyone recognize this master cylinder? Looking to replace it as its obviously leaking. Its a 2-bolt so a little different from the genaric juice-brake masters. I just need something that will fit Thanks.

Thanks for the suggestions. I have called the builder and he has not responded. Could be due to health issues but we’ll see. Removed the belt from the alternator and noise seems to have gonna away. Maybe the alternator bearing is toast? I will take it for a longer drive this afternoon to be...

Well i seem to have developed quite the noise that seemd to be coming from the oil pan? The best I can describe is it sounds like some pebbles in the pan and a slapping noise like a frayed belt. Happens in neutral as well as driving, at about 2500rpm. There is no rythm to it like a bad...

My roof rack would be for hockey equipment and such so a rear luggage rack would make it smell like exhaust.

Is there any bolt on style roof rack available for a 35 sedan? I wouldnt mind modifying the rack to fit but definitly dont want to drill into my car. Ive seen those drip rail clamp-on type but my 35 doesnt have channels there just kind of a lip.

Ive noticed now on 2 seperate engines that im having an issue of the outside of the heat riser holes tearing away from the intake gasket. Is this a common issue or should I be looking for a cause? Both planes are square and intakes were true. I used white grease all over the gasket. Im...

I was able to make mone by cutting kerfswhere the bend was and forming over the sides. I tried to soak/steam and just wasted money on firewood. Looks tacky from the underside but its usually closed.

Ive taken it out the inside several times now. Actually pretty quick if everything goes the way it should. Maybe 2 hours or so. If you pulled the ****** mount off and obviously the shift tower im sure you could pull it out the bottom.

The 41t is on the heads. Nothing cast on the bellhousing. The vibrations happens in neutral or on the road. Had the flywheel balanced with the clutch cover before install. This happened wth both the stromberg it came with as well as the new speedway 97’s on a 2x2.

Ive got my rebuilt 41T motor swapped into my 35 sedan. It seems as though there is a rough spot right around 2100 -2400 rpm. Is this standard on these flatheads? The original motor had a little vibration right around 2200 rpm as well so im not sure. Ive got an electronic ignition with 2x2...

Thanks for all the suggestions. Looks like ill be pulling it back apart!

Im trying to install an electronic crab distributor -speedway 910-8353 in my 39 motor. The engine starts and runs but id like to get some more info on adjustments. Is this thing adjusted by loosening the 3 mounting bolts? Where are they normally set? My motor has no timing marks so without...

Has anyone done this? I am working on a 35 sedan and would like it to sit just a bit lower. However the Mitchell OD doesnt look like it has too much more room over it. Just curious if I need to look at more cutting or if another approach is necessary. Thanks

No problems with chatter. Just kind of cheap insurance to not pull this motor back out. Definitly replacing the disc tho! I know there is a million shops out there but i’ve gotten ahold of 1 that can even balance a flywheel on their own without “sending it out” aka charging more than is...

So is this the 28-34 style clutch/pressure plate that i need to order?

Ok so looks like I’ll go with the earlier flywheel with the 9” seeing as I can barely find a machine shop around here that will resurface/balance a flathead flywheel and thought I was crazy about re-drilling for another pressure plate. Next question- when looking at the replacement clutch/...