Search results

Still looking. Bought a couple off ebay, but they are both right side.

back to the top - still looking

Still looking for this one piece of trim. Thanks

Still looking.

Hi - I am getting ready to put my hood back on my 1940 Ford deluxe coupe and I can't find one piece of stainless trim. I need the drivers side smaller front piece (3 rib?#. I have all the other pieces, but as small parts will do after a two year project it can't be found. You can see where the...

One of my rear window seals won't lie flat in the corner as described in original thread. I would be willing to try heat gun, but I'm concerned about paint damage. Is there a technique or heat range that would instill more confidence on using this technique and not hurting new paint job? Thanks

Thanks for the response. I'm still not getting it. I was just out playing with the handle and couldn't get it to catch. Without the notches it seems to slide right out. What is the function of the threaded screw hole in the base? The aftermarket handles only have a short allen screw in them...

Hi - I have aftermarket exterior door handles for my 1940 coupe. I do not have any originals to copy (car came to me as a pile of parts). I understand there is a notch near the end of the square shaft. Can someone post a picture or give me dimensions to make the correct notch on my handles? I...

I just installed my 'Drake' front and rear bumpers on my 1940 Ford coupe. In both cases the outside holes lined up nicely, but the inner brackets had to be pushed into position. I also had a 1939 bumper where the holes are lined up differently than a '40' Ford. Be sure that the brackets sent are...

I'm starting the final assembly of my 1940 Ford coupe and I can't find three of the springs that go into the headlight buckets. There are four springs in each of the buckets that are part of the adjustment mechanism for the headlights. I know that I can buy a kit, but I only need three springs...

I believe this window regulator is the drivers side for a 1940 Ford coupe (I got it with a project '40' coupe I bought that I installed power windows). Be sure by looking at the pictures that it will work for you! Condition is very good to excellent - very tight and very minor wear on large gear...

I have name brand parts coming, but you guys have me worried that it will just be for show - and not actually work when it rains. I like everything to work on my cars, so I'll do whatever it takes to get there. Again, thanks for the information.

Thanks for the responses to correct my windshield wiper ignorance. I have ordered everything to get me going - hopefully.

I am in the process of reassemblying my 1940 deluxe coupe and need to get the windshield wiper mechanism installed. I bought this as an old neglected project car and have absolutely no parts to the windshield wipers. I was thinking Specialty Products cable drive would be a good way to go, but...

Don't start redrilling holes - yet! Make sure the the "reveal" is lined up (as already mentioned) and the holes should align at the same time. Typically if trim doesn't line up it means there's a problem on how the door hangs and / or the body needs shimming. I just put my '40' body back on the...

I'm putting my '40' Ford deluxe coupe back together now. I switched the wood block and spare tire bracket to the drivers side to make room for the battery, but it was originally (when I got it anyway) on the passenger side. The tire faces the trunk. My coupe has the jump seats behind the front...

Hi - I'm almost to the point where I can start installing glass in my coupe. The only glass I got with the "project" car was the wind wing / vent glass. I can make templates for all the glass, but really need to be accurate for the door window glass width. Can someone measure their coupe door...

Thanks for the responses. As far as I know the "grooved" trim is for the 1940 Ford. I presently have the drivers door trim and I think I have found the passenger side. I am still looking for the rear quarter trim. If I don't find something soon I will try the The Early Ford Store.

Hi - I just went through my exterior trim / moulding for my 1940 Ford deluxe coupe project and found that I am short the passenger side door and both rear quarter panel pieces. I seem to have a lot of sedan pieces and not much coupe stuff. I need very nice pieces, ideally just need polishing. I...