Search results

Carl G, That's my kind of ingenuity. Way to go! Thanks, 1961

My '61' Galaxie 2dr came with Ford factory/dealer installed under dash air conditioning. At least this is the information I have compiled. I like the looks of the under dash unit, chrome and very period. What I don,t like is the boat anchor compressor and over built mounting bracket. It hides...

Thanks to everybody, all good info. Yeh, they were leather. The new ones I got are double lipped rubber with a spring band. Again, A BIG THANKS.

Thanks to everybody for your comments, very helpful. I got lucky and found the oem seal on none other then ebay. Perfect fit, I did not want to be a three time loser. If anybody needs one it is ebay item number 222232848192 and Ford part number B4A-6698A. Thanks again.

Thanks to everyone for helping me with the oil pan gasket seal. I've moved on to the oil pump pick up tube where it goes into the oil pump. Again, it's my '61' 292 Y block. The seal for this connection that comes with the oil pan gasket set(FELPRO) looks nothing like the original that I took...

Thanks to everyone for the comments. Sounds like 'less' is 'more' in this case. I'm just going to sneak up on it and play it safe. Thanks again, 1961.

I'm looking for the correct torque for my 1961 292ci Y block oil pan bolts. I torqued the last one to factory spec (factory manual) of 12 ft. lbs. It squirted out the side in pieces like a banana. It was a FELPRO and I used Permatex Ultra Gray sealant. I started at 5 lbs. then 10 lbs. then...

That's what I thought, it seems that the gaskets are there to displace moisture and stop any rust from starting between the different parts. Thank you for your time.

I'd like to start by thanking everybody that replied to my questions about my oil filter and proper oil to use on my project. I'm reassembling the rear end housing and want to know if I need to use gasket sealer on the "housing to brake backing plate gasket" and "brake backing plate to axle...

A lot of great information. On my way to Walmart. Thanks to everybody. Reverend, I'll take mine with butter and salt.

Part two- Should I use a high zinc oil in this engine as well? Thanks again.

I have a '61' Galaxie with a 292ci. It appears to have an oil filter adapter on the engine instead of a canister. Would anybody know what filter number would be used on this application. Any make and number would be good as I could cross reference for my choice. I can only read a portion of the...

Bingo! OK, that was easy. Thank you. (first time ford resto)

I'm replacing the rear axle bearings in my '61' Galaxie. I don't see any rear axle seals. Is this typical for this year and model? The bearing is a ball bearing assembly with seals on both sides. Would that be it? Seems like gear oil would sneak out elsewhere. Any comments or help would be...

I have a '61' Galaxie 2 door and was wondering if a '63' Galaxie 2 door chassis/frame is the same as a '61'? Looking at pictures I can't see any difference with the exception of a convertible, mine is not. Thanks for your time and thanks for reading my post.

Thank you, too easy.

Just a wealth of information from everybody. It has headed me in the exact direction I needed to go with my project. Thanks to everyone that offered up their input. You guys are a great well rounded group. And I don't mean your waistlines. Thanks Again, 1961.

I have a "61" Galaxie with a 292 and I've installed a fresh FordoMatic. Must I use hard trans cooler lines (originals are bent-junk) and also has anyone gone with just an aftermarket cooler? Would a stand alone cooler do the job? If this has worked for anybody else I'd like to hear about it...

When engine is hot and you get it restarted do you notice any black smoke from the exhaust? Check your exhaust manifold heat riser to see that it hasn't failed in the closed position, happened to me. Caused the engine to run much warmer on the gauge. All of the exhaust going back through the...

I want to install a new front crank seal in the timing cover. I noticed that the timing cover gasket comes two ways. One with a short front section of oil pan gasket and one without. Factory manual says to remove the oil pan. Has anybody done this either way and what are the pros and cons. Next...