Search results

10-4 Tom, looking forward to firing this thing up soon.

Roger that, we'll give her a shot.

Its point type. The man I bought it from had never put it into in any thing and didn't know how it was set up. I would think a modern dist like this would be set up for a 12volt neg ground system out of the box. But I don't know?

Picked this Mallory up the other day and cant find any info on it as far as wiring it into a stock wiring harness. I don't plan on changing from a 6volt pos ground system. But I don't know how to wire this into my stock harness? Wiring is not my specialty, can you shed some light on this for me?

I did when I purchased the cam. It's a ohv cam that he recommended with the 1.5 to 1 ratio Miller set up.

Roger that. I was under the impression for some reason the marks would be in alignment at TDC. Thanks.

Hello folks. Let me start by adding this is my first adventure in A land. I am getting started on my miller ohv conversion and I have a 350 cam from Stipe I will be installing. My question is, is the timing pin just used for finding TDC. If I want to pull the cam, should I line up the pin mark...

Converting an A model to juice. 540-875-9991 Jesse

I didnt do any welding with the gen intact it was disasembled. It took a good weld and seems pretty dang strong 3/8 steel with a 2 1/2x3 square washer. This was not my first choice but there is no material on the intake to remove. I have ordered another intake that the sales rep said I could...

I have a copy of John Lawsons book with him building a flathead and doing 400+ dyno runs in the process and hp was gained with the risers. I cut the mount off a old gen and made one with the right width and welded it as close to the front as possible. It does line up with the other pulleys now...

:mad:Thought I found a intake that I could use. 2 issues that I have are that the intake slot for the gen is 3/16 larger than the gen. The other is the fan pulley is a 1/2 more towards the rad than the other pulleys. What gives guys I cann't find a intake that works.

I put a dual carb intake on my 35 and went to install the gen and it sits in the grove on the intake very sloppy. Measured the gen base it is 2 1/2 inches and the intake slot is 2 11/16. Nothing is worn out nice crisp 90 deg edges. I am not pleased with the fit between the two parts, does anyone...

I have a edmunds dual carb intake I would like to run on my 21 stud. Does any one sell a longer rod? Can I mig weld an extension or should I braze it?

I pulled the intake and the vent tube is there, so I attempted to pull the pan but couldn't get it off, I had the front end out and trans un bolted and motor jacked up till it was hittting the fire wall but I did get it up enough to see I had the wrong gasket. Called the neighbor he had bought a...

Ok some of you have been helping me with an oil leak and this is what I found today. The baffle in the oil pan has a slit cut clean down to the bottom, why I have no idea. My question now is do I weld This slit up to the top, or was this slit just carried down more for some reason at some point...

I'm almost positive that it has the correct oil pan gasket on it, the kit came with gaskets for two style pans and the ones I have left over aren't the right ones.

Walt, The vent tube you talk about if it is not install the oil in the valley will fall stright down to the oil pan and leak out of the baffle? The motor I put in the truck was a fresh sleeve rebuild that my grandpa had stashed away for 20 yrs. I looked at the motor I pulled and I did see the...

In the pass side front of the pan is what looks to me like a bafffle or maybe an overflow. The oil level on the stick is about an 1/8th inch above the full mark and there is oil leaking out of this spot. Is this a overflow or do I need to pull the pan and look into this further. My experence...

I will not be shopping there any more. In my last order I ordered two wheel studs and two head light stand bolts. They sent me two studs and two more studs in the bolt package, called them up and they told me that it is impossible because the parts are prepackaged before they get them. Buddy I...

Wired my 35 and I can only run one headlight with out blowing a 30amp fuse. It will run both for about 20 sec. Thought it may have been in one of the headight harness (short) so I switched lights from one side to the other but can only burn one. I do not have a radio or a heater. What amp fuse...