Search results

hello about what synders calls a 'curved interior panel ' a-161ab '. not sure what edge goes up; it has a rounded edge and bended edge. which edge is attached to the rumble seat riser? thakns

hello does anyone know where I can find dimensions length width and depthof back rest and seat? thank you

.........................................................

hello please excuse my not knowing proper names 1- does anyone know the distance between center points of stantions? 2- in the past there was a substance used to fill defects in curved bows. I cant find that post. the post said it would hold upholstery tack. does anyone remember that...

i think i made it too confusing can any body tell me or show pix how to attach seat back to package tray? the top of wood seat back seems to have an upward curve thanks to all

hello thank you in advance how does the top wood piece of the seat back which is flat with an upward curvature attach or fit into the sheet metal package tray? i hope i am using the correct word for the package tray. the tray on the leading edge is flat, so it seems the wood could not screw...

hello will hand cranking with fuel turned off, oil the the cylinders? would this be a good idea for cars not used frequently and in cold weather? thanks in advance

hello i can get 27" batting off the shelf locally i don't have order or get a large amount the seat springs are about 42" i am an amateur upholsterer i understand cotton batting is the best my ques is: can i join peices of batting to form a larger piece and if so best way to do so...

hello my car could not be all original the bottom steering wheel to seat is only 6" the distance fr upper front edge of seat is 26" to a depressed clutch pedal. i put the seat platform[ called riser?] where prior holes were found. does the 6" seem too short and the 26" seem too long...

hello my car does not seem to be all original. after installing the seat, the clearance from bottom of steering wheel to seat is only 6" and the distance from front edge of seat to pedal in depressed position is 26" which seems too long. do these distance seem ok? or does seat needs to be...

hello how to attach springs to front riser? in reading 20 pagesof posts on the Barn the concensus says the springs go on top of the riser without wood. but no where do they say how. there is a tab on each side of the riser but they are below the top of riser so that is not the answer. other...

hello again i bought a model A 30 roadster in pieces i complained to the Barn latelty that sills/rails did not match frame now am in the process of installing firewall and : throttle foot pedal wont clear bottom of firewall and clutch pedal wont clear bottotm of frewall should firewalls be...

restored approx 5 yrs ago pictures taken in barn are not the best,sorry

Hello about the rails and riveted on floor pans as one “ unit” 0- i’m an amateur 1- i think my alleged 31 roadster “unit”is something else other than even 28 to 31 coupe or roadster 2-per m0del A serial number table and frame mark stamp number, it is a 31 frame 3-the car is in pieces but...

30 roadster does frame webbing go under fron fenders? thank you

i have a nice 27 t which i want to sell but don't want it turned into a hot rod- it's too nice for that. any ideas how to sell?

i have put in 4 ring washers on the water pump with the 180 degrees apart and still leaks.. i dont notice any scarring of the shaft. should i tr y 2 more washers or give up and buy a leakless water pump? thank you

there is a video on the net of someone cleaning a tank by putting pellets and vinegar in the tank and shaking it. does this work? it seems that because the tank has 5 segments that this method would not work. by the way, how does gas get out of the other 4 segments and into the main segment and...

hello carb puts out a lot of gas into the air horn when engaging the starter--any ideas? thank you

hello 1. will a NAA type B generator work on a model A? 2. to check out in field or armature, does anyone know the ohms in field to ground and armature to grnd? 3. by the way , i cant motor it right now as i have no 6v battery to check it out thanks