Search results

Has anyone used the Reproduction shift forks? Are they any good? Thanks, Randy

I just put a rebuilt handle on my 29 Sport Coupe, locked it, tried to unlock it and the cylinder turns completely around and will not retract the lock bar. Is there any way to remove the handle without destroying it??? Thanks, Randy

I dropped the pan to fix a small oil leak and also the rear main cap today. When I took off the rear main cap there is no oil groove in the babbit???? - What is the best way to cut the groove? - how far from each end of the cap do I start the groove? - how deep is the groove? Now I guess I...

What would be the problem with substituting a long needle bearing for the center spacer on the cluster gear shaft? I have a new reproduction spacer, basically a piece of galvanized pipe, it fits loosely in the gear and on the shaft, seems like it would just rattle and make noise where the...

Just started up the new engine and transmision and Houston WE Have a Knock. I thought it was in the engine but when I depressed the clutch the knock stoped. The knock speeds up and slows down with the idle speed. I can feel the knock on the bottom rear half of the transmission case. I took the...

Does the top hidem welt on a 29 Sport Coupe kill on top of the belt rail trim as it comes down the rear of the door pillar or does the hidem continue above the belt rail unit it gets to the rear top curtain? I have seen it both ways, which one is correct? Thanks, Randy

I am looking for a original good horn rod, 45 3/4", for my 1929 Sport Coupe. Thanks, Randy

Is there a wire in the horn rod?

I am looking for a restored 1929 nickel plated rumble handle. Thanks, Randy

I am looking for a restored nickel plated raditor shell for my 29 Sport Coupe. Thanks, Randy

I am looking for an original outer gas gauge nut in good shape. Thanks, Randy

What kind of support/attachment does the seat back rest have at the bottom of the frame? The top of the frame sits on the package shelf and has two bent steel brackets that fit into the slots on the top of the package shelf. I see that there are 3 holes in the top of the curved seat riser floor...

I have a Lebaron Bonney top that was purchased back in 1975, when I aquired my 29 Sport Coupe as a youngster, still new in the box along with the rest of the upholstery kit. The top is plain tan canvas, I have seen alot of photos of Sport Coupe tops using a material that looks alot more similar...

How thick is the wood nailer for the rumble seat side panels for a 29 Sport Coupe. I have attached a picture of the nailer. Thanks, Randy

What is the correct way to fasten the quarter panel trim pieces for a 29 sport coupe? I have attached a picture of the area. There is a steel bracket behind the panel where the fasteners are shown, does it have a wood piece attached to it or is the trim supposed to be attached directly the the...

I am replacing the wood header above the windshield in my 29 Sport Coupe and after much sanding trimming and @#$% it now fits the header cover. It attaches through the metal panel above the winshield with a carrige bolt on each end of the header. Finally the question, there are 5 or 6...

How do you treat (miter?) the corners of the glass bedding matarial. Are there any tricks to getting the glass and bedding into the frame? Thanks, Randy

My Sport Coupe had no wood or hardware when I got it so I have some questions now that it is time to fit the new wood. - Are the three bolts that attach the door header wood to the metal door header strip carriage bolts? - Does the nailed on door header trim go between the door header wood and...

I spent all day trying to get the doors on my 29 Sport Coupe to close with no results. I started out with 2 pads under each body block. I have a gap at the bottom of the door post a gap at the top of the door post and the middle of the door at the latch hits the door post. I removed one pad...

I am looking for a pair of rain gutters for a 29 Sport Coupe. Thanks, Randy