Search results

Can someone post a pic of the back side of the glove box door with a clock installed for a 35. I need to see what the installation is supposed to look like. I have the all the pieces, its a Borg clock, and want to make a correct install. Thanks

Does anyone know when Ford started using the fordoor rear door panels with the pouch flaps? I've seen what appears to be original upholstery 25 and 26's with them and I need to confirm they were used on 25's. Thanks for any help.

Looking for a left front shock ( drivers side ) for a 35. Doesn't have to work but must turn

Can someone point me in the right direction to find the installed lenghts of the head studs for a 35 with aluminum heads. I know I've seen it somewhere but over the years, sometimes I forgets. Thanks

Looking for a 1935 glove box clock. Prefer Borg but would consider Jaeger. Doesn't have to be perfect, just all there. I will be in Hershey all four days if you will might have one there. PM with info.

When I got my 35 Convertible Sedan back in "64" it didn't have a glove box clock. I've found a reference that says it was supposed to have one. The car is an early build - probably April/May 35. Can anyone put me on the right path - is it supposed to have one or not? Carolina-Bob

I need a full set (8) of Champion 7 plugs for a 35 as originally equipped. NOS or real good used OK. You can PM with condition, qty, $. Thanks

Looking for a good set (8) of Champion C-7 3 piece plugs for use in a 35. PM with $$$. I'll take less than a full set or whatever, I just need to get to 8. Thanks Bob

Looking for a decent set of tubes for my 35, particularly the drivers side tube. I don't need rustouts, or really dented ones, I already have those. Thanks for looking.

Need a bit of help remembering the location of the body stripe on a 35. I can't seem to find it anywhere and I can't get my brain in the right gear. I think it's either 5/8 or 3/4" below the belt crease. I'm ready to put the stripe on my conv. sedan and I would like to get it in the right...

Were these painted, plated, plain, or what? I can't seem to find it mentioned anywhere in the books I have. Thanks

I am in need of a reputable engine rebuilder within a days drive of NC that can pour and line bore the mains as well as anything else it might need. Any suggestions?

Hey guys I have a fairly fresh, rebuilt 4 years then stored, 35 221 flathead that I fired up a couple of weeks ago. It sounds good when cold to luke warm, a little lifter noise is all, but after getting warmed up there is a definite knock in the engine. I tried shorting the plugs one by one...

Does anyone have any tips or other secret methods of putting those awful little wire spring clips in the trim or do you have to slide every clip in from the end? I fought every one of them on my hood trim. I've squeezed and bent and tried all sorts of other things and thought I would see if...

Do the horns on a 35 have to be isolated from the frame so they will only ground through the horn switch. I have couple repop horns that work fine as long as they are not connected to the car. When they are bolted to the fender braces the wiring gets real hot real quick. Unbolt them and hold...

Can someone describe or post a picture of how the triangular shaped brackets between the taillight and the frame mount. I forgot how they mounted when I took them out 20 years ago and I can't figure them out now. Must be CRS. Thanks guys

Does anyone make a battery that will fit in a 35 without having to modify the frame mountings? I've been looking at the net and can not find anything less than 8 in. tall. Thanks in advance. If Henry had not put it under the floor, no problem, but !!!!.

Hi guys: I have the battery seal that goes in front of the battery and the holes in the seal match up with holes in the front of the battery cover. My question is what connects the seal to the cover? or is it supposed to connect to the floorpan? I don't have a 35/36 to look at so I'm hoping...