Search results

Here ya go

need turtle decklid for 26-27 roadster

I am going to install a 3/4 race camshaft that I have had in stock for a long time. Wolverine brand out of Michigan it is in mint condition and in the box. On the box it says settings are .013 and .015 hot. How do you do them hot or set cold at what number. Anybody. Fred

looking to identify sizes on following numbers: 99A-6211C, O1TS-6211K, C31T-6211K, C01TS-6211K, C31T-6211Q. Thanks Guys.

I am working on my 34 roadster that I bought in pieces in 1970. The rear section has the panel with the latch for a trunk. Where would the trunk hinges be located and on what? The coupes with trunks are bolted to the water trough under the rear window. I looked up in the 33-34 body book and the...

I would like to take out a couple of leaves in a 40 n.o.s. front spring with the covers on. Has anyone removed the covers without cutting with a snips? Kube where are you. Anyone?

Going thru some ring and pinions to inventory(have had for some 40 years) and came across an odd one. 48-Center case with a 10 tooth pinion and the ring gear is 39 teeth. The pinion has the marking 10-39 and is ford script. Ratio 3:90 what is this for quicker off the line than 3:78? Anybody...

Is it just me or are these repro weatherstrips for the 33 and 34 fords made for the repo windshields. I am having a hard time putting one in a original early take-off windshield with script glass. If this task is as hard as I am making it the guys at the ford plant in Michigan at the time were...

Finally got around to starting up my new 36LB engine. Runs great now I want to wire the generator. Ignition turned on the ammeter goes negative(likes it is supposed to do). There is 2 wires coming out of the 3 brush gen. Where do these 2 wires go? The wire from under the dash that is at the fuse...

Installing my 34 3W door check strap(nos) but the 3W has wood in the "B" pillar. I looked at my other 34's and they all have 2 screw holes for small bolts to hold it to metal "B" pillars. What now? Any help from someone with a 3W that can take a peek? Thanks in advance Fred

I knew I had one but could not lay my hands on it. I am reluctant to say anything unless it is in front of me. Well I found it 11C-8215B N.O.S. Where are you buyer? PM me if you wish.

Had trouble finding the right words to search. In the ford bulletins it says with an eye dropper fill with the red fluid to the bottom line on the gauge if the gas tank is empty. I have about a gallon of gas so I think I can be a little above the bottom line correct.? Then just fasten the tube...

I want to learn something new today. have been trying to figure it out myself but have come to the realization i need your help. How do you turn on the domelamp on a 3W. The switch on the bottom of the dash on the left is for the dash lights. There is no switch on the B pillars like sedans. so...

Bought a set of flathead cylinder heads today from a older gentleman who had a lot of racing equipment. These are cast iron and center dump 24 stud and have the ford script with the part number 99A-S Never have seen any in all my scrounging. Information anyone? Thanks in advance.

I have a nice original w/s frame and glass. I cleaned all the old seal out of the groove around the window. I slipped in a new w.s seal and it fits perfectly, but here is the question. Do you put some weatherstrip cement in the groove to hold it in place? It wants to come out when I try to get...

here is the picture

David J went thru some pans for the 3 window. All are the same but I have one that is a little shorter than all the others. I would guess about 3 inches. What does this fit? Anyone..

I know this has been talked about a lot mentioning early v/8 garage in california making this set-up. I think his name is Richard Lacy. I put his set-up on my 1934 3 window and I could not have been happier. You know when you buy something and it actually works and does what it is supposed to do...

29 mODEL A quit. took off cover and half the teeth were gone. i know this is common. took the nut off and got the bad gear off(fibre) and was ready to put on a aluminum one i had. for the life of me i can not find a mark on the crank gear to line up to the cam gear. washed all the teeth and...

Looking for a nos rear bumper guard for ranch wagon or custom 300. thanks