Search results

hello fellas, I have a dana 41 that needs a new pinion seal, mac's has one but it doesn't look right. here is a picture of my seal and of mac's. what do you think? should I order it? https://www.fordbarn.com/attachments/281309/ https://www.fordbarn.com/attachments/281310/

hi everyone, a while back I was on ebay looking around and found someone selling new remanufactured steel lower fenders, the place claims they are made in the USA. they were real pricey. I went back to ebay to try to find the fenders and now I see they are no longer listed, or I'm not looking in...

hello fellas, do you guys know what year this might be?. the fella I got the block from said it came out of a 52 pickup. it has hardened seats.

hello everyone, I'm in need of an oil pan.......do you guys know if anyone makes pans for this flathead block?

GREAT FORD MOTOR STORY -- A Ford Airplane - This was 6 months BEFORE Pearl Harbor! Henry Ford was determined that he could mass produce bombers just as he had done with cars, so he built the Willow Run assembly plant in Michigan. It was the world's largest building under one roof at the time...

hi fellas, do you know if the f100 pickup frame is the same on the f250 for the 1954 year? as in length? I have a box from a f100 and would like to put it on a f250 truck.....thank you.

check this out, http://www.ford-trucks.com/wp-content/uploads/2014/07/2008-Ford-F-450-Chassis-Cab-XLT-Interior-Manual-Transmission-Stick-Shift-Home.jpg too bad the younger gen. wont know how fun it was to drive with three pedals in a new ford

hi fellas, does anyone know where I can get a good 2 prong temp sending unit? I have had 2 in the last 2 years that have failed. thanks for your time. Kendall

hello fellas, my 1949 pickup is stuck in third gear and i think its because of one of the three clips (see picture). there are 3 clips, i dont know that name of them but anyways they are next to the brass syncros. one of the clips does not go down like the other 2 to let the gear slide...

hi fellas, i have a chance to buy a 1947 ford coupe, it has a rebuilt flathead. body is very good with new paint, new tires, and interior has been re done. i have searched on the internet for a blue book value with no luck. would you guys know of a web site where i could punch in the year and...

Hello fellas, I have a question about exhaust temperature. Would anyone know why my 8BA exhaust temp is about 100 degrees hotter on the front exhaust outlets than the rear? The engine runs fine, and never over heats. I point the thermo gun on the heads and they are steady at 160 to 180...

hi fellas, i am working on my 49 F1 and need or would like to anyways replace the insulated firewall cover in the cab. the old one is falling apart and there is not much left of it.....any who....i seen LMC trucks has a insulated ABS plastic firewall cover for my year. before i spend the money...

i was wondering if the 72cc edelbrock heads would be better then the 62cc 1115 heads. does anyone know what the compresion would be from one to the other on a standard 8ba? 8.1 to maybe 9.1 on the 1116 heads? would you even tell a differance in proformance? .......just thinking and was wondering...

hello, i am in need of a drive and driven speedometer gears for a 3 on the floor ****** from a 49 F1 pickup. the part number on my drive gear is worn so i cant see it, does it mak a diffreance as to what the drive gear part number is? can i stick just any in it if i find one close? or do any of...

RM Auctions to Sell the World's Oldest Working Vehicle in October Every weekend around the country there's an auction selling a rare automobile or piece of ephemera that is priceless to collectors. But on Oct. 7, RM Auctions will be able to say it truly has something that's...

hello everyone, 9 inch rear end out of what??????..... would be a good bolt in for a F1? i am looking for a little better road speed with out rapping out my flathead. right now going down the highway at 40 mph the engine is running 2000 rpm. i am thinking a 9 inch with 3.50 gears. .......but...

what is the best way to check to see if your generator is charging the battery with a volt meter??????

i an having problems with my heads holding coolant. the studs look fine but the head to block leaks bad, i pulled the heads and going to try new gaskets again. what would seal better copper or the carbon graphite by best gasket? i have copper on now and was thinking trying the graphite. thanks

Before I fry something I have a question about polarizing the voltage regulator. I have a rebuilt generator and I don’t want to damage it, I am getting very close to firing up a fresh rebuilt flathead just converted to 12 volt. My question for you guys is, when I take the batt wire from the...

hi everyone, i am looking for a fan shroud for a V8 EAB. does anyone know if there is any after market shops out there that sells these? thanks kendall