Search results

Looking for a good usable Original FoMoCo top of a 32 Ford car shell if some one has a none usable Shell , top parts of one , Piece needed shell itself , at least 5 inches on both sides of where bull nose /Basil mounts leading edge (insert) including radator cap hole to back side of shell (...

I am interested has anyone here on the Barn used or sent Original parts to Steele Rubber Products ,located in North Carolina. They state that the parts are Made exactly to originals. So a lot of us that work on 32 Ford's and other years know that the reproduction Parts from drakes and others are...

Does anyone know if a 30-31 & 32 B (4 cyl) radiator core /tank and brackets ( shell mounting down the sides) are the same between the three years, I know the radiator have different bracket for the support rods ,32 narrower & has tab /bracket for hood hinge, 30-31 wider for support rods.

Looking to buy a good condition Ford 32 5 w Passenger side inside A pillar/ windshield Trim . Stock length

Orginal 1932 car wheels & more Set of 5 Orignal Restord / paited " apple green " 32 18 inch Rims With New Firestone 5.50 tires $900.00 32 I belive Orignal paited spaire tie spreader bar $140.00 Orignal 32 headlight bar model B "no hole " $190.00 540-659-6655

Ford Original steel front fenders left & Right no well. $650.00 pair Tried to load pics , will not allowe Send email for 540-659-6655

sold Sold

Is Bill Wzorek still rebuilding shock's , I sent him a pm over Two mouth's ago with no replie back . Has he retired, if so who would also rebuild's ,I have two front shock's That Leak ,

Did a search did not find what I was looking for , On my 32, ( I did not Restore / 1950 Modified Build ) I removed the hub caps and found that the studs are .150 thousand to short from even coming flush with lug nut , only .350 worth of threads used , so at least .400 to short of a stud , The...

""Sold"1932 speedo Good working used 1932 Ford speedo, $170 shipped in upper 48 ,

In my 32 , I have a slight modified 39 Flatty, with 39 Trans , Offenhauser Regular Dual with 2 94 , Mallory ignition , Edelbrock heads ,Open Edmond air filter with K&N elements , 2 psi to carb's . Timing 8 deg at 700rpm Total 27 @ 1800 The issue that I am having , 1st gear to 3,500 rpm...

I know what a trip odometer is , Why does the S&W only go to 99, & the purpose of the three steps on the stem, Or is it not a Trip odometer, Also was there a extension for the stem or did you reach your hand under dash to reset

Are original Ford wire wheels Safe , Would you trust to drive them over 400 miles a week & on average Speed of 60mph , or some times 80 mph! I have a original set of 1932 For my 32 Todur with 40 brakes , I know I need adaptor , wheel are nice , No pitting or Rust ,

Looking for a nice Original set of 32 Ford close car swing arms. Thanks

Looking for information , opinion & experience !! I have searched hear & on the Internet but unable to find what I'm looking for, I have two car's , One is a 1930 Sedan , Hot Rod , Not a street Rod ! With a 4 bar front suspension , cross steer , I drive the car about 300 miles a week , & have...

Looking for a Original 90MPH Good working Order , Good color ,& number's Restored or Original , Prefer Stewart Warner,

I have a 1939 Flat head in my 32 Ford , 39 ****** , some one installed a Offenhauser Dual Carb intake , with 91-99 Ford carb's , Non Progressive linkage , with a Mallory unlight dizzy (12 v ) @ 600 rpm's , timing set @ 6 deg & total 26 at 2,000rpm, Plug's autolite 65 gap .030 If it has a...

I did a search , Are these backing plate 42-48 , is the brake adjustment the Sam as 39-41 , and the master cylinder That looks triangle , the fill cap , is there a gasket ? If so what does it look like, I tried to use a o-ring , then the treads would not catch / start , Thanks

Can someone post a pic of a 1932 Ford Sedan rear window garnish ,

Looking for inner fender from inner fender to quarter panel belt line where the fender welting would go , Coupe / Roaster preferred or may be sedan , Around this condition or better ??? Send pic , thanks Ed