Search results

My motor is basically stock with a lion speed 4 head and headers....internals are all stock.....I installed a FSI electronic distributor (not the zipper) and been running it at that for a couple years, but would like to fine tune it...they say to set initial timing at 0 then advance till it...

SOLD Have complete Clings adapter for 37-39 V8 ****** to banger motor. Brand new, never used $400.00 for everything picked up here or add shipping. tried posting pics but this site wont do it...e me and I can provide pics if needed.

Here’s my issue....1930 tudor...right hand door is in locked position, so I can’t rotate shaft enough to release it from latch...no key...how do I remove this door latch so I can replace. I can get the door open from slop in old latch but would like to replace it so I can lock it.

Has anyone installed a PVC valve in a banger engine. If so, any tips. Thanks Ron

picked up a new starter for my 37 21 stud engine. What is the brass/copper strap for that is attached to the stud.

just picked up a new starter for my 21 stud 37 engine. What is the brass/copper strap for that is attached. the original starter did not have one.

Have brand new, never used 9" pressure plate, disc and alignment tool. bought 9" when I needed 10" $120.00 shipped thanks Ron

the new rod bearings for my 37 are flanged. Do these still need to be fitted using the hammer method?

Looking to determine if 1937 21 stud engine crank is ground undersize. Looked in oil groove of main bearing and nothing but on the back of the shell it says....Ford (script) USA-T G2....do these numbers mean anything to anyone Thanks Ron

can anyone tell me that the main bearing thrust dimensions are on a standard main bearing, im looking for the thickness of the thrust flange on the bearing. Ive got a little excess clearance but the thrust surfaces look to be worn a little thin and wondering if a new set of bearing shells will...

are intake manifolds interchangeable between 21 and 24 stud motors. thanks

My 30 Tudor has the passenger door lock in the locked position with no key. Ive tried removing all the screws and rotating as far as I can but the shaft is just short of rotating enough to remove it from the door. I would like to be able to lock/unlock this door, but cant get the door handle...

found a 37 ****** to go with my 37 21 stud for my 30 Tudor. The 37 trans is complete less tail section and u joint. Can i use the tail section off my 30 trans on this 37 trans. if not what do I need to have to couple it to my closed drive line. Thanks Ron

I see this motor has no rear main seal but has a slinger instead. Do these motors with slingers only leak and if so how bad, or is there a way to install a rope seal. Little confused here and being a 37 with first year insert bearings, not alot of info to be found. Im sure some of you have dealt...

have 37 21 stud motor with 3 ring aluminum domed pistons 30 over. looking for rings for these. everything I can find shows second ring to have expansion ring underneath, but my pistons have standard style first and second rings with 3 piece bottom ring. I have found some rings marked...

have 37 21 stud engine that i need correct piston rings for. this motor has aluminum 3 ring pistons that has two upper rings , compression and wiper and an lower 3 piece oil ring with expander. all the ring sets i can find show expanders under the upper two rings as well, but my pistons dont...

looking for a 39 ****** in decent shape for my 30 Tudor. Ron, Fresno, Ca

have a 30 Tudor. All new steering balls, Teflon easy steer buttons, shorter pitman arm, all new king pins and bushings, new tires. Steers easy with front wheels off the ground but really hard with tires sitting on ground. Checked the king pin thrust bearing is taking the weight of the car so am...

have 30 Tudor that I've installed 4" dropped axle, stock spindles and 40 juice brakes. what is the best way to lower the tie rod to clear the motor, wishbone and such. the bolt to bolt spread on spindle is 3" so later model steering arms won't fit. does anyone make dropped steering arms for this?