Search results

  1. O

    Wheel paint

    Where is a good place to order wheel paint (tacoma creme) and have it shipped. I need 1 quart of single-stage.
  2. O

    Winfield head

    I just bought a sedan that has a Winfield head. The stamp on it is 03–112. One; what does the stamp mean? Two; what is the compression ratio? Three; how much is the head worth?
  3. O

    Install of master shut off switch

    How would you cable this?
  4. O

    2 dumb a** stupid questions

    1: Does anyone know why ford made the terminal box dogbones? It would have been more expensive than a nut or wingnut, and a nut or wingnut would be easier to install. 2: Why is a condenser fiber washer needed when the screw, screws into metal?
  5. O

    Mount Washington

    For those of you who have driven up Mount Washington, you know what a thrill it is, and how white-knuckled it can be going around some of the turns with sheer cliffs on both sides. I have had the pleasure of doing it with a modern car many times and with my A one time (never again). If you do...
  6. O

    New shoes on a cast iron drum dont fit

    I remember reading that some other people had the same problem, but I could not find the answer. I purchased Snyders Part # A-2019-M, A-2021-X soft molded brake lining. These are going on 2 year old cast drums. I have the clicker all the way in, I can barely get the drums on, and once on they...
  7. O

    Assembling the Model A body from the factory

    https://www.facebook.com/reel/1578676353604751
  8. O

    31 Rear wheel bearing seal

    What do you use to remove the rear wheel bearing seal?
  9. O

    Brake Lining Material

    Is one type of lining better for cast iron and one type better for steel?
  10. O

    Shut off valve under the tank

    What’s a good lubricant to put inside the shut off valve under the tank to keep it smooth running.
  11. O

    LEDs for parking lamps

    Has anyone found any LED’s that are short enough to work in a 30/31 roadster cowl lamps?
  12. O

    Leak down test and a compression test

    I am interested in knowing what you think of this leak down test. The other day I went for about an hour ride at the end of the ride the car really started running ratty. When I got home, I pulled all the plugs. Number one and two plugs were very fouled and oily. Number three and 4 had a nice...
  13. O

    Original condenser?

    Is this an original Ford condenser? It tests out at .288
  14. O

    packing bearings

    I have always packed bearings by hand. Are there any advantages to a bearing packer? https://www.amazon.com/GearWrench-2775D-Hand-Bearing-Packer/dp/B0002NYDYE/?tag=atomicindus08-20 https://www.amazon.com/gp/product/B0B1MK52NW/?tag=atomicindus08-20...
  15. O

    Snap-on MT-335 coil/condenser tester

    I bought this Snap-on MT-335 a while ago and just got to testing it. I cant get it to work. Has anyone used this tester with good results? Does anyone have a good manual?
  16. O

    Drag link, tie rod torque

    Do you guys actually torque your drag links and tie rods to 25 foot pounds or do you just do the 25% tightening?
  17. O

    Brake adjustments, stick or no stick

    When you adjust the brakes, do you use the wooden stick with 3 notches, or do you make the adjustments without the stick?
  18. O

    Blowing fuse issues with 30 amp fuse

    Any ideas where to start looking or what to do. While driving the car blew a fuse and died. Every time I try to put a new fuse in the fuse instantly burns. I am running 6 V with a perTronics electronic ignition.
  19. O

    Marvell carburetor

    I have two Marvell carburetors. But both power valve holes are not the same. One is smaller than the other. What is the correct hole diameter?
  20. O

    Alignment issue 31

    What would cause this? For a while, my roadster has been pulling slightly to the right. It is more noticeable the faster I go. I noticed that the right front tire has been wearing out on the outside edge. I changed that tire to the left rear. I have radials. I changed the toe in to 1/16 and...
Back
Top