Search results

I have a 39 transmission for rebuild. will need input shaft. I comes with shipping box made by Vanpelt. I also have a 37 trans. rear x mount $75

I have a pair of 1936 headlight rims. They are stainless and in very nice condition. No dents or rust Satisfaction guaranteed $50 shipped lower 48 SOLD

Is there a difference between 1935 and 1936 front fenders? I am aware of the rear fenders! I seem to have two different fenders, one has much less of a ridge down the center and it does not seem to have been worked on too much. thanks

I have a steering box marked 01-a 3550. It has a roller sector gear and will fit the 36 mounting bracket. I have never seen this number nor heard of a roller sector in 1936. 1 purchased this gear box from a vender I North Carolina.

I have a intake 2x2 intake manifold that was on an engine that came out of a car in the late fifties. It is definitely of the Hexagon 2x2 design But is marked with Evans in the normally Hexagon Places. It is in good condition with no cracks or stripped threads. If interested make me an offer. I...

Can a 1936 steering box be modified to accept the 37 roller to replave the original sector. thanks. Jim

I have one 1934 and one 1936 original bumper Good straight need plating. $100 each plus shipping.

I have been searching the threads but have not found a clear answer. Will f100 backing plates fit and work on my 39 axels and be able to retain the wide 5 wheels. Thanks for the help, Jim Haskins

One 1934 and one 36 bumper, straight and good for plating, $125 ea. Evans 2x2 intake manifold, made for marine or racecar use, carbs are reversed, $250. Reserfaced flywheel and new FORT WAYNE clutch for 49 to 53 Ford. $200 buyer pays shipping.

I need help making a 39 trans. Connect to an 8BA 9.5" clutch..It seams the coller for the through bearing on the 1 3/8 " shaft interferes with fingers on the pressure plate, and the through bearing does not contact the clutch.I read on the H.A.M.B that the only fix was a 10 or 11" clutch...

Can somebody reccomend a fabricator or body shop to replace the front floor pan in my 36 coupe, in the Spokane WA area. I thought I could save it but am recnsiddering it. Thanks Jim Haskins

Which is the best driver side exhaust manifold for use on a dual exhaust setup on an 8BA in a 36 coupe Thanks for your help.

Can somebody tell me the correct position of the ell head bolt that holds the clamsheel to the trans. I thought ths flat would go to the center of the housing.Vanpelts drawing shows it laying in the rubber slot. Mac is out today or I would ask him. Thanks I would like to get this done this...

I cannot identify nor locate a flywheel starter ring for an 8BA flywheel with a 91/2 " clutch. The ring has an 12 3/4 ID, has 112 teeth and it is 5/8" from the tip of the tooth to the ring ID. The 49/53 ring is too large the59a ring is too small. Help will be greatly appreciated.

Hi All, I am replacing the burned out steel headers on 8BA in a 36 coupe. It seems the installer had to bash the drivers side for clearance. I would like to install Fenton headers. Question" Will Fenton headers clear the 1937 steering box , If so are there any other problems that I should be...

Can someone help identify this box. Casting numbers found appear to be 91a-3550. there is also a circled B and the number 10 on it. It was purchased as a 37 box, but does not look like one I have seen. There is no light or horn box switch accommodation on the bottom .a small hole only. Thanks...

What engine is referenced by 8RTCRS I was told it was a 53 with a 4" crank.this number found on canadian rebuilders tag. thanks

Right side rear fender 1936 sedan. NOS. This is not a repop. has been stored for over 50 years. It is perfect condition. original grey paint. $500 . I will deliver to the shipper of your choice for packing and shipping, or make other arrangements as needed. Jim 360-270-1358. SOLD THANKS ALL

I would like to reove the fuel tank from my 36 coupe for rust remval. IT LOOKS LIKE THE FILLER PIPE HAS TO BE CUT, ARE THERE ANY MORE SUGGESTIONS OR ADVICE. THANKS.