Search results

I am installing a new cork gasket in the rear block. After installing seems that the crank will not go all the way down.Am I missing something here? I am thinking I need to bolt the cap down and tighten.

Been having a lot of oil coming out the clutch housing bottom. Checked the tube not clogged. Also clearance was 15.This is the second time trying to fix this problem. Removed the motor out this time. I did find this piece that was loose. lt looks like a piece that was added. With this loose...

How much movement should a valve have in a valve guide? It appears that there is some gap causing the valve to rock back and forth. So how would you tell if it is time to change? it is very little but there is movement. I have had a lot of blow by. Thinking of up grading to later valves and adj...

This all started with the rear Main leaking bad. I started with dropping pan and checking rear main tube for blockage. Checked clearance it was .0015 on the rear main. Put it all back together and still oil slick. Then I took a compression check 1-3-4 all 120lbs I did install a 6.1 high...

First I dropped the pan to check rear main for blockage in the tube going out the slinger. I did recently add a High compression Head 6.5. I did a compression check all cylinders 1,4,3 120lbs number 2 no compression squirt some oil in and up to 60lbs. The rear main cap on the bottom has a grove...

Replacing Pan gasket . Ordered it from a supplier and it came with everything needed to do the job. One thing the rail cork gasket had no holes. Is this normal? Well low and behold there were some holes .. You could not see them until marking out to punch holes. Like some have said here there...

Looking for bezel for gauges for my 30 roadster. Show quality not needed. Patina welcome. I have a re pop to shinny for my taste.Thanks

How to you mount the windscreen? I see to holes at the top nothing there to anchor to. Can someone give me some direction how to attach.

If someone could help with these Hinges for the trunk lid. It looks like the top hole is for the pin on the trunk lid. This hinge has pin in the center. What Am I missing? None of the holes are counter sunk.

I have the chance to get a cable drive tach. Where do you attach the cable to. Is there a drive that attached to Dizzy?.Any help would be great. Thanks George

Looking for outside door handles for Roadster 1930 31.. Thanks George

The Roadster is mounted on a frame in the pics. The best I can tell is the lower hinge on the bottom when closing door moves to the rear. Also the lower inside Bottom is hitting the cowl. I have tightened the hinge and still moves back and forth. So before I screw any thing up is the re any...

Could someone give me a rough Idea of the weight of a roadster Body and frame? A rough guess would be great. Trying to ship. Body only frame. Thanks

I got my brakes back from Randy Gross which were like new.. Beautiful Job the driver side rear drum was hitting the backing plate so Randy sent some shims. I put one in and now the drum does not go all the way in. there is a gap between the drum and backing plate. Any advise would be great.. I...

Will the front fenders off a 1930 31 Tudor work on a 1930 Coupe? It looks like they will but need to be sure because the splash aprons are the same or look like they would work.

Trying to put a RPU Together with fenders and running boards .I do have a set of 31s off a Sedan. Or what would be the correct ones. Thanks

Thanks Ford Barn and Ya"ll For the Search section for doing repair on our Model A . I needed to change the Crankshaft pulley and I did a little Search and saw were it was said to put your wrench on the drivers side frame and rock the starter, bada bing nut came right off.It was a beautiful...

I pulled the motor out to install a new clutch along with freeing up the travel on the throwout bearing fork. Removed the motor no problem installed the new clutch when I went to reinstall motor had it on a pretty good angle when oil starting coming out The back. New to these banger motors...

I am having a problem adjusting the fingers on a new clutch. I have made a nice tool for the proper height of the finger the problem after adjusting and it is nuts on I go to stake and it all moves. I guess I am not a staker.. By the way I am using locktite..Would using nylock nuts be ok? It...

Body is in Very Good condition. No Rust. No patch panels. Cant seem to load pics. Pm and I can send. SOLD!!!