Search results

Had 66 mustang with 289 sitting outside garage a few days on hill . Gas ran down into engine thru carburetor and flooded whole engine . Drained engine replaced oil but now no start, check all fire,timing, and took valve covers off and looks like water in engine. Never seen anything like this...

Backing in driveway today felt bump in transmission reverse went out , only 150,000 on truck can’t believe this . Rolled back and has foreword no reverse , best option to have rebuilt or buy rebuilt or used ? Thanks in advance.

Trying to date this photo of my dad and uncle . Do you think the car on left is a 49,50 or 51 ford ? Thanks in advance .

Thinking about swapping my generator to an alternator while I have motor out of my 60 falcon . What components would I need to change from factory generator set up ? Worth the trouble?

My 74 bronco had an issue when dimmer switch was pressed the headlights go off , replaced switch and got new halogen headlights with relay and harness. . After all that still same . I checked plug at dimmer and with jumper one side and middle wire turns on lights and other side with jumper seems...

Got back on my 60 falcon after taking it apart 12 years ago , motor cleaned and painted but there is so much grease on the transmission I have scraped and sprayed it several times but still not clean . When I took it out it was working ok with a little hard shift into second but wondered if...

I am in the middle of getting ac installed in my 74 bronco . Got the compressor mounted and condensor coil but I have a 1963 under dash unit and started looking at new units . Have any of you put in a under dash with heat and air . They are about the same price but other than making more room...

Wanted a 302 motor and transmission for 1974 bronco . Motor running ok could just use C4 transmission .

Looks like my transmission is on the way out . Shifts from first to second at about 18 mph and into 3rd about 24. Some times it long shifts into third. I changed the filter screen and made sure fluid level is perfect at hot idle . Is there really any kind of mystery oil that really helps ? Or...

What would you suggest the best carburetor for my 1974 bronco that has a 289 in it . It was said to have a 302 in it when I bought it but manifold says 289. Motor runs great on minute then won't crank then runs rough . Can't get old carb adjusted just want to change it. Has an autolite 2100 with...

Finally found a early bronco I could buy at the right price. almost a barn find he had it painted several years ago and put it under the awning next to the barn with the chickens. Said he wanted to drive his other one so he just parked it. After getting all the junk off it to move to my trailer...

Has bondo and fiberglass filler came so far along that no one uses lead anymore. Being a plumber I know all the warnings about lead but it is pretty easy to fill small holes. I was thinking about using some to build up some deep dings in my car.

Had a 1960 falcon for years getting ready to complete my restoration . Would like better brakes on rear . They do not make a kit for 4 lug rims . Has any one tried a ford ranger rear axle with disc brakes. It is only about a half inch wider and I would have to use 5 lug rims. Thanks for any...

Got a 1960 falcon I had had for many years . Finally getting around to complete and put on road again . Want to change rear end to disc brakes but there are no kits for 6 cyl 4 lug. I have herd that it is possible to use a ford ranger rear end it is with in about half inch of same width. I know...

Can some one tell me what has to be done to correct this problem? After taking off all the paint on my 60 falcon I have some bleed thru my primer in spots I did not touch . Will I have to sand down and remove what ever is under this primer to fix this problem?

I guess I am one of the worst in the world about throwing something away I think I can some day reuse. I got this motor and transmission from a friends estate. Know nothing about it but it is complete and it is a lightning 6. What do you think?

NOS Wagner master cylinder assembly # 8A-2140 B Fits ford 1949-1959 $90 plus shipping Have 2 will sell both for 170

Just a few more parts , these are ford pistons that was told were for a model but just not sure.

Ok here comes the dumb questions. I have bought all the parts in a group and have some books but can not figure out what some of the stuff can be . If any one can help me with ID of any of this or what they may fit like the carbs and manifolds . was told most of it was ford model A but I am not...

I have access to a lot of small A model parts , I have no idea what some are just by looking . engine parts , manifold and other misc. If you know a part you need please send me a photo to coheley5@comcast.net I must decide which parts I want to save before they are all scrapped .