Has anyone had this carb issue? Main jet separated!

Ayers1

Ayers1

Well-known member
Took my car out for a ride last night and got about a mile from home when it sputtered and died. Got out to see what was going on and gas was pouring from the carburetor. Couldn't figure it out on the side of the road so I had to tow it home. Got the carburetor apart and saw the main jet had lost a piece. Upon further investigation I found the missing piece laying in the port feeding 3&4 cylinder. Thank goodness that I didn't just fix and try starting it up! Have you ever seen this happen before?
 

Attachments

  • 20240813_204749.jpg
    20240813_204749.jpg
    58.6 KB · Views: 91
  • 20240813_204736.jpg
    20240813_204736.jpg
    84 KB · Views: 83
Ayers1 said:
Took my car out for a ride last night and got about a mile from home when it sputtered and died. Got out to see what was going on and gas was pouring from the carburetor. Couldn't figure it out on the side of the road so I had to tow it home. Got the carburetor apart and saw the main jet had lost a piece. Upon further investigation I found the missing piece laying in the port feeding 3&4 cylinder. Thank goodness that I didn't just fix and try starting it up! Have you ever seen this happen before?
Click to expand...

Never seen that happen before. There's always a first time.
 
I have been around A's my entire life and don't remember seeing this before either! P.S. I'm glad it wasn't just me.
Fyi, I'm not sure if this was an original or a reproduction.
 
Yes left original right repro
 

Attachments

  • main jets.jpg
    main jets.jpg
    33.9 KB · Views: 75
  • carbs.jpg
    carbs.jpg
    72.3 KB · Views: 26
Both pictures are of the same part. Together is what it's supposed to look like, apart is how I found it.
 
The Ford engineers generally knew what they were doing and only made a few mistakes. People making reproduction parts should pay attention.
 
I agree nkaminar! If you look closely at the picture you'll see little to no solder on either piece. No wonder it came apart!
 
More “high quality “ parts ,been fighting them since start of restoration. Lot of people making this repro junk really don’t care and the vendor that sell it has to suffer complaints from customers.
 
gdmn852 said:
More “high quality “ parts ,been fighting them since start of restoration. Lot of people making this repro junk really don’t care and the vendor that sell it has to suffer complaints from customers.
Click to expand...


Yes it is!
 
Ayers1 said:
I agree nkaminar! If you look closely at the picture you'll see little to no solder on either piece. No wonder it came apart!
Click to expand...
They are not soldered press fit only! reproduction parts!
 

Attachments

  • main jet no solder.jpg
    main jet no solder.jpg
    47.5 KB · Views: 15
  • walter dripping nose.jpg
    walter dripping nose.jpg
    19 KB · Views: 6
ON a RHD car, the long jet that hangs down when the bottom is taken off (can't remember its name) usually gets bent when that is done because the steering box prevents it dropping straight down. Not well thought through! After a while, bend, straighten, bend straighten etc becomes too much and it breaks. I've seen it a number of times
 
Synchro909 said:
ON a RHD car, the long jet that hangs down when the bottom is taken off (can't remember its name) usually gets bent when that is done because the steering box prevents it dropping straight down. Not well thought through! After a while, bend, straighten, bend straighten etc becomes too much and it breaks. I've seen it a number of times
Click to expand...
idle jet it is!:)
 
You must log in or register to reply here.
Back
Top