Zenith carburetor paint

Tom Endy said:
Several have suggested Por-15. I used this product on several Zenith carburetors a number of years ago. It does not hold up well against fuel and constant heat cycling. When first applied it gives the carburetor a plastic look. After a few years of service it will begin to peel off like a bad sunburn. See photo. Tom Endy
Click to expand...


The POR-15 failed because there was some other paint beneath it. Surface preparation for POR-15 requires degreasing and phosphoric acid bath - No primer. POR-15 adheres best to a rusty surface; seasoned metal and sandblasted surfaces are also acceptable.

From the POR-15 web site - "POR-15 works because it chemically bonds to rusted metal and forms a rock- hard, non-porous coating that won't crack, chip, or peel. It keeps moisture away from metal with a coating that is strengthened by continued exposure to moisture"

The only caution for POR-15 is that it must be top coated if exposed to UV.
 

Attachments

  • AE3A84D5-67E5-4CB1-A2D5-B3EE8D99F2FC.jpeg
    AE3A84D5-67E5-4CB1-A2D5-B3EE8D99F2FC.jpeg
    68 KB · Views: 61
Tom Endy said:
My thanks to all that responded to this post with suggestions. In particular, D.J. Moordigan who suggested a company called Brodak. I contacted then and have ordered a small container of their fuel resistant black paint.

Several have suggested Por-15. I used this product on several Zenith carburetors a number of years ago. It does not hold up well against fuel and constant heat cycling. When first applied it gives the carburetor a plastic look. After a few years of service it will begin to peel off like a bad sunburn. See photo.

Tom Endy
Click to expand...


Read post 21 !!! What Dollar Bill says hits the nail on the head . It was very obvious to me when I saw the picture . If a person can't follow the supplied instructions , to the letter , Its best not to use the product . Any type finish will fail without proper surface prep as well .
 
Last edited:
My thanks again to D. J. Moordigan, post #12. I ordered a can of black fuel proof paint from Brodak. It is a dull black and is certainly fuel proof. I dipped the head of a bead blasted bolt in the paint and let it sit overnight. I then submerged it in gasoline for several hours. The paint remained unaffected.

I also obtained a can of similar paint from Sig mfg Co. It is a gloss black and is also fool proof as I subjected to the same bolt test.

Both companies have a web site. Brodak is located in Pennsylvania and had no trouble shipping to me in California.

Both paints are called a Butyrate dope.
Brodak is dull black
Sig is gloss black

See the attached.

Tom Endy
 

Attachments

Tom Endy said:
My thanks again to D. J. Moordigan, post #12. I ordered a can of black fuel proof paint from Brodak. It is a dull black and is certainly fuel proof. I dipped the head of a bead blasted bolt in the paint and let it sit overnight. I then submerged it in gasoline for several hours. The paint remained unaffected.

I also obtained a can of similar paint from Sig mfg Co. It is a gloss black and is also fool proof as I subjected to the same bolt test.

Both companies have a web site. Brodak is located in Pennsylvania and had no trouble shipping to me in California.

Both paints are called a Butyrate dope.
Brodak is dull black
Sig is gloss black

See the attached.

Tom Endy
Click to expand...

Thanks Tom for the thread and the follow up.
 
The Pontypool japan black is the high gloss version of 'Japan black'. this may be closest to the version used to flow paint Model T's. You may be able to add rosin to it to flatten the finish to be close to the carb paint desired
 
Brodak's dope is made by Randolph Products. I get mine from Wick's Aircraft Supply. Aircraft Spuce and Specialty is another supplier of Randolph dope.
Cheapest by the gallon. AeroGloss a Pactra product is no longer available, bought out by Midwest Products. Been building R/C models for years.
 
I use black Rust Oleum Engine paint. Gasoline resistant, great color, very lasting. I paint all my carburetors with this.
 
You must log in or register to reply here.
Back
Top