timing pin substitute

ericr

ericr

Well-known member
do any of you guys remember a substitute timing pin that was sold some years ago, that was spring-loaded, such that you did not have to unscrew the timing pin., merely press it on it till it fell into the dimple, then release?

did anyone ever buy it? does anyone still make it?
 
never seen that accessory before! it is different because the thing I used to see was a permanent installation.

I suppose part of the theory was if you started the engine without removing the "fumble pin", as it was called in the old ads, it hogs out the dimple.
 
I bought one in Hershey, made of brass. Well done and works as advertised. I don't leave it in the timing cover, just screw it into the cover when I use it, then replace the original timing pin when done. I found it in the chocolate field across from Tam's, but forgot the vendors name.
 
Yes, I've run one for years. I don't remember where I bought it and would buy an extra one if I saw them on the market. Sorry I don't remember, but it has worked great, never a problem
 
I think some one here on the barn showed one they had made themselves a while ago. Making one shouldn't be too difficult but as is often the case, it might not be worth the effort if one is available cheap enough commercially.
 
29spcoupe said:
I bought one in Hershey, made of brass. Well done and works as advertised. I don't leave it in the timing cover, just screw it into the cover when I use it, then replace the original timing pin when done. I found it in the chocolate field across from Tam's, but forgot the vendors name.
Click to expand...

Spring loaded brass thing with a keychain ring? I Got one - amazingly simple and effective tool! about the size of the timing pin itself.
 
29spcoupe said:
I went out to the garage to take a picture, can't find it. I put it somewhere so I wouldn't loose it, and now I can't find it. I'll have to look tomorrow in the daylight.
Click to expand...

sure its not in the car in a tool box or attached to the ign key?:D

id post a pic but dont know the seller and wouldn't want to undermine his sales by people making thier own if someone remembers the name or has a contact others could buy from him that would be great! - I did hear snyders bought a whole buncha them to sell in thier catalogs - I dont know if the guy has caught up for that large of order or not :P
 
29spcoupe said:
I went out to the garage to take a picture, can't find it. I put it somewhere so I wouldn't loose it, and now I can't find it. I'll have to look tomorrow in the daylight.
Click to expand...

Haven't we all done that! Never clean up your workshop if you ever want to find stuff again.:D
 
29spcoupe said:
I went out to the garage to take a picture, can't find it. I put it somewhere so I wouldn't loose it, and now I can't find it. I'll have to look tomorrow in the daylight.
Click to expand...

I do that all the time. Why does it always backfire?:eek:

Timing is a cause of backfiring. I better check my timing. :D
 
Post #15: "Alway shows up when your not looking for it!!!"
_______________________________________

Yeah - but by the time you see it again , you don't remember that you were ever looking for it ! :):D:confused::o:(
 
Put the pin in with rubber bands holding it in. Hand crank slowly using both hands and watch the pin slip into timing dimple then STOP ! You got it . Throw away the rubber bands cause you Won't remember where there are. Always change rubbers as needed.
 
steve smith said:
Put the pin in with rubber bands holding it in. Hand crank slowly using both hands and watch the pin slip into timing dimple then STOP ! You got it . Throw away the rubber bands cause you Won't remember where there are. Always change rubbers as needed.
Click to expand...


That's what my dad told me:)
 
You must log in or register to reply here.
Back
Top