thermostats

[Clem Clement]

Does an eV-8 require two thermostats?

 

[JSeery]

Yep, there are two totally separate cooling systems except for internal to the radiator.

 

[Henry/Kokomo]

Yes sir. One for each cylinder bank.

 

[GB SISSON]

And each side needs a 170 degree thermostat made for a subaru. Put them in last week and I have never seen such fast warm-up and steady temps. The napa part # is in my shop.

 

[kycowman]

Would you post the napa part # when yiu get it? Thanks

 

[Steves46]

And each side needs a 170 degree thermostat made for a subaru. Put them in last week and I have never seen such fast warm-up and steady temps. The napa part # is in my shop.

I have a set on my 46 and they have been absolutely superb. If I was close to my garage I could provide the P/N but I'm sure someone else will post it soon.

 

[GB SISSON]

Balkamp brand from Napa. Part # 111. And made in USA of all places.

 

[Ford Freak]

I have a set in mine as well . Got them @ Pep Boys .

 

[petehoovie]

Can't seem to find it on the NAPA site. Can someone post a picture?....

 

[38bill]

Dont have a NAPA nearby here is one on Ebay.

http://www.ebay.com/itm/like/401255884451?chn=ps&dispItem=1

 

[Ross F-1]

Can't seem to find it on the NAPA site. Can someone post a picture?....

https://www.napaonline.com/en/p/MRD111

 

[petehoovie]

Thanks, guys....I see that the one pictured on the NAPA site has a rubber grommet around its circumference where as the one on eBay does not....

 

[Clem Clement]

Thanks guys. MY '39 Peekup had only the right on. No wonder it always wanted to turn left!

 

[Old Henry]

Thanks, guys....I see that the one pictured on the NAPA site has a rubber grommet around its circumference where as the one on eBay does not....

Lose the rubber gasket. It just rolls off when you put the hose on and messes things up. Hold the stat down like this:

This is the best thermostat that I have found for year 'round, all temperature, all altitude use: the Stant 14157.

The one I used I bought from O'Reilly as their part # 2962 that was in a Murray box # 4157 but it's the same as the NAPA # THM 111 and the Stant # 14157. All the same stat manufactured by the same manufacturer for a 1990 Subaru Justy.

 

[GB SISSON]

One of the many reasons I love the net as it pertains to the auto world. Who'd a thunk it? Subaru stats in a flathead v8..... My steel pipes pretty much meet against the outlets on the heads keeping the thermostats from rising up. My napa only had about 8" piece of hose so I cut it into four short pieces. And Henry, I love the look of your engine compartment and some may say you need to upgrade your wires etc., but as my physics teacher used to say..." The proof of the pudding is in the eating".

 

[Clem Clement]

Thanks. Where do the safety wires go: drilled holes in the head?

 

[weemark]

Thanks. Where do the safety wires go: drilled holes in the head?

safety wires just go down the side of the inlet and are held in place once the hose gets pushed down on them then clamped.

 

[Clem Clement]

Ah: thanks.

 

[mhsprecher]

Clem,

I was able to put stats on my 45 truck without the Henry wire system. I got Stant stats from one of the suppliers. For my 39, I am trying Bob Shewman's stats that go up in the top hoses. All have worked well so far, although the passenger side cylinder bank on my 45 truck warms up pretty high before cooling down, even with new stats, so I am not sure what is up with that.

 

[Clem Clement]

Thanks. I have some new ones coming from NAPA. The old ones were well down in the hose and sideways.