Quick Flathead question for everyone

C

capt280

Junior Member
Will a T5 transmission for a ford (unknown year) work on a 8BA Flathead. Seems what i have been reading is the S10 T5 is the go to choice.

Thanks in advance for everyones help
 
I believe that the difference is the location of the shifting mechanism. The S10 is farther forward than the mustang type.
 
capt280 said:
Will a T5 transmission for a ford (unknown year) work on a 8BA Flathead. Seems what i have been reading is the S10 T5 is the go to choice.
Thanks in advance for everyones help
Click to expand...

The late '80s/early '90s Mustang W/C T-5 is a better choice over an S-10 because of better ratios, internal improvements and higher strength, but the S-10 tail housing swap moves the shifter forward and next to the gear box. A 1" adapter will mate the trans to any '49-'53 Ford/'51-'53 Mercury bell housing.
 
V8 Bob said:
The late '80s/early '90s Mustang W/C T-5 is a better choice over an S-10 because of better ratios, internal improvements and higher strength, but the S-10 tail housing swap moves the shifter forward and next to the gear box. A 1" adapter will mate the trans to any '49-'53 Ford/'51-'53 Mercury bell housing.
Click to expand...

Almost, you need the half-bell and the hogshead plus the adapter plate or a half-bell and one of the aftermarket cast adapters.

First photo is an aftermarket cast adapter
Second photo is half-bell, hogshead & 1 inch plate adapter
Third photo is line drawing using a half-bell and aftermarket cast adapter
Forth photo is half-bell, hogshead, 1 inch plate adapter & S10 T5
 

Attachments

  • th.jpg
    th.jpg
    7.3 KB · Views: 37
  • 4spdhogshead.jpg
    4spdhogshead.jpg
    33.4 KB · Views: 41
  • 8ba%20-wct5%205272ass.jpg
    8ba%20-wct5%205272ass.jpg
    43 KB · Views: 41
  • DSCN1858.jpg
    DSCN1858.jpg
    108.5 KB · Views: 59
Hi..i'm in the way to put Ford t5 on my potvin powered flathead,,and i see that there are other ways to put the shift level forward,,,a remote lever mechanism is the right way,in a mustang web page there is one type for sale....other easy way i try is to buy a opel corsa c shift lever.....or at least is not really difficult to build one yourself......
 
JSeery said:
Almost, you need the half-bell and the hogshead plus the adapter plate or a half-bell and one of the aftermarket cast adapters........
Click to expand...

You just need this 1" adapter for a Mustang T-5 to bolt to the '49-'53 Ford/'51-'53 Mercury bells. A '51 Mercury is the one shown and is what I'm using in my avatar.







MCFadapter2.jpg


MCFadapter1.jpg
 
Last edited:
Definitely go for the late model Mustang. Better ratios and MANY improvements over the S-10.. I have used the 1" adapter plate but for my current build I am using a Quick Time bellhousing from Speedway Motors. Not cheap ($570.00) but I believe it will hold the critical engine to trans alignment more accurately..
 
V8 Bob said:
You just need this 1" adapter for a Mustang T-5 to bolt to the '49-'53 Ford/'51-'53 Mercury bells. A '51 Mercury is the one shown and is what I'm using in my avatar.
Click to expand...

V8 Bob you are correct! I was thinking the earlier years 8ba Mercs and trucks. I am going to have to slow down on my reading!!!

I like the remote shifter using the original shifter location and shifter. That's what I am using with a Ford T5z transmission.
 

Attachments

  • shifter over cover 2.jpg
    shifter over cover 2.jpg
    36.6 KB · Views: 84
Last edited:
V8 Bob
Where did you get that adapter, I've been making them, but this is a better and cheaper way to go
 
JSeery said:
Believe Wilcap has them. V8 Bob what years of the bellhousing has the cross-shaft clutch fork setup?
Click to expand...

The major production '51 Mercury bell housing was the only year for the '40-'48 cross shaft clutch release. ( JFYI, I'm using a '32-'39 cross shaft in the one pictured.)
A few early '51s used the '49-'50 stamped steel 1/2 bell and round patterned transmissions.
 
That adapter works with the 49-53 Ford and Mid 51 merc bell housings using all stock parts except the disk.
 
V8 Bob said:
The major production '51 Mercury bell housing was the only year for the '40-'48 cross shaft clutch release. ( JFYI, I'm using a '32-'39 cross shaft in the one pictured.)
A few early '51s used the '49-'50 stamped steel 1/2 bell and round patterned transmissions.
Click to expand...

I had never seen one, didn't know they existed! Thanks.
 
You must log in or register to reply here.
Back
Top