Patching some nasty 1936 rear fenders

Rusk

Rusk

Senior Member
I know a bunch of you have been down this road. The rear fenders that I got with my car had lots of dents and tears and someone did a really poor job patching the rot where they meet the running boards. Since nice rear fenders are hard to come by (and big $$), I decided to fix what I had. Here are a few pics I took as I went along...

14185215717_9f09864a09_c.jpg


14185100930_92444c0768_c.jpg


I removed all the bondo and fiberglass and cut out the rot. Then I made a new patch and welded it in...

14348572356_37984faa15_c.jpg


Welds cleaned up...

14370376442_72314a5d72_c.jpg


14370377292_c52630feb7_c.jpg



Here's the other fender. It got the same patch and some other repairs. I spent many hours with a hammer and dolly and some time with a shrinking disc to get it to this point...still needs a little more before it'll be ready for primer.

14391848693_65bd7c62fe_c.jpg



14391847933_93695fa5c9_c.jpg



I still need to drill the holes for the running boards and make the reinforcements for the inside.

I also had my buddy make a patch for my firewall on his Pullmax (I only have hand tools). We intentionally matched the passenger side X, but we could have made it like the original with the square if we'd wanted.

14371663075_f3c67b26c5_c.jpg


14370746104_66fe30cfd2_c.jpg


That's it. I just wanted to share the way I tackled some common problems my car.
 
Good work Rusk, it is real rewarding when you undertake the repairs yourself, Well done.
 
Great job of making patches and welding in, what type of welder, again you get great satisfaction to know you did it yourself. Zeke
 
To be able to afford the new repros or find nice nos and afford those is one thing but doing a nice job at saving originals is something special. Good job Rusk! I need to learn how to weld sheetmetal myself. Wondering if you used a mig or tig to do those welds?
 
Wow! Awesome repairs and craftsmanship. Beautiful thing, keeping the original sheet metal on the road at the expense of using up our time and passion instead of just money! No offense meant to folks who prefer the checkbook shaped wrench, it is a bitchin' tool. To some, seeing that much progress in a thread that takes two seconds to look at is unintentionally deceiving, like reality t.v.:D How many hours into just one fender?
 
Nice work. Having done a few like that myself, I know the man hours and beers involved getting results like that.
 
WOW! That looks great Rusk.May I make a suggestion? It looks as though you are using a sanding disc for stripping.If you have a Harbor Freight nearby,they sell a 4-1/2" polycarbide abrasive wheel that fits an angle grinder (#60571).They leave very fine scratches in the metal and last a long time as long as you don't hit a sharp edge.They remove light surface rust and paint(after chemical stripper) like crazy and will not gouge the steel.Pretty cheap,6-8 bucks. I did a little experiment with one of the inside window trim pieces on my car.I stripped it with the wheel,etch primed,sealed then painted with base/clear.No swirls or scratches showed. Have fun!
 
Very nice work. I wish I could do that myself!!! I was lucky and found a good body guy to rescue my 35 panel delivery fenders. Here's his repair of the rear section of my front fender............
 

Attachments

  • Pass side fender small.jpg
    Pass side fender small.jpg
    44.6 KB · Views: 111
Thanks guys. I used a Miller TIG welder for these repairs. I used to MIG everything, but I never liked the way the seams on sheetmetal turned out. The welds are just too hard and brittle to planish flat, although I have seen some guys prove me wrong. The heat control on the TIG works better on thin stuff like these old fenders.

the cooch said:
How many hours into just one fender?
Click to expand...

I would guess at least 50 hours per fender...they were pretty bad. Glad I'm not paying myself! :)

I found a couple more pics of the driver's side...

14375286915_2a77623a87_c.jpg


14188727580_2d17a998c7_c.jpg


Willit Stop said:
WOW! That looks great Rusk.May I make a suggestion? It looks as though you are using a sanding disc for stripping.If you have a Harbor Freight nearby,they sell a 4-1/2" polycarbide abrasive wheel that fits an angle grinder (#60571).They leave very fine scratches in the metal and last a long time as long as you don't hit a sharp edge.They remove light surface rust and paint(after chemical stripper) like crazy and will not gouge the steel.Pretty cheap,6-8 bucks. I did a little experiment with one of the inside window trim pieces on my car.I stripped it with the wheel,etch primed,sealed then painted with base/clear.No swirls or scratches showed. Have fun!
Click to expand...

Thanks...I'm always looking for options, so I'll have to check that out. I use everything from a body file, DA, Scotchbrite, 3M stripping disc, and various abrasives. I try to keep from removing any parent metal when possible.

Don Rogers said:
Very nice work. I wish I could do that myself!!! I was lucky and found a good body guy to rescue my 35 panel delivery fenders. Here's his repair of the rear section of my front fender............
Click to expand...

Looks good!
 
Ahhh the TIG welder. Thanks! Wow, 50 hours each is gonna show when your car is done. You ARE paying yourself, in future compliments! Nice work, again. -Chris
 
Looks great. I got a front one that I am going to cut and piece as you did in order to have a spare front clip.
 
I'm just starting this process on all four fenders on my 36. First, I tackled a running board. So far, it has been frustrating and humbling. Your work show that it can be done and I'll keep after it, hoping to end up as well as you did.
 
You must log in or register to reply here.
Back
Top