Now what the @?&$

V

vern hodgson

Well-known member
Ok, was able to finagle the spark rod into submission, next was to install the starter rod and the hole is almost one and a half inches off to the left. Engine is centered in frame and cowl seems sitting where it belongs. What would cause this much misalignment?? This body comes from Canada.
 

Attachments

  • image.jpg
    image.jpg
    70.7 KB · Views: 729
Crazy question, was this the original purpose for the curved starter rod?? Was the cowl penetration relocated at some point? What is a good measuring point for the horizontal location of the penetration and what would that be in inches?
 
I just went out and looked at mine. That hole is off. Are you sure that rod is mounted correctly? There is no way that is in the right position..Canadian or not.
 
vern hodgson said:
Ok, was able to finagle the spark rod into submission, next was to install the starter rod and the hole is almost one and a half inches off to the left. Engine is centered in frame and cowl seems sitting where it belongs. What would cause this much misalignment?? This body comes from Canada.
Click to expand...

The hole for the starter rod was offset to the passenger side on the earlier 1928 bodies, hence the offset starter rod. Can you tell us a little more about your body. IE: What year is it? Left hand emergency brake? Any other of the VE28 features?
 
dlshady said:
The hole for the starter rod was offset to the passenger side on the earlier 1928 bodies, hence the offset starter rod. Can you tell us a little more about your body. IE: What year is it? Left hand emergency brake? Any other of the VE28 features?
Click to expand...

The car was assembled in Canada, a Tudor, fire wall date is 1928, e brake is pistol grip, on right side of gear shift. Have never seen date on the frame. Vern
 
I know very little about the VE28's.

Restoration guidelines;

The offset starter switch rod was obsolete at about
vehicle 50,000.
 

Attachments

  • Early28 starter.jpg
    Early28 starter.jpg
    47.3 KB · Views: 478
Last edited:
Tom Wesenberg said:
The parking brake lever is by the left kick panel for the first 5 months.
Click to expand...

This is probably the easiest way to tell quickly, but unfortunately the brake lever hole remained for a while after the brake lever was moved to the center. On top of that, the starter rod was changed to a straight rod quite a while before the brake lever was moved, so it's not a dead giveaway. The earliest Tudor bodies had several unique features that would help to pinpoint the production date of the body but most are difficult to explain without showing photos.

As for the firewall date, it's very likely the gas tank may have been changed somewhere along the line so the date isn't a dead giveaway either. Same with the emergency brake lever on the transmission. It's very likely that the transmission top was changed over the years.

Is there a body number stamped onto the subrail underneath the front of the driver seat? That would be helpful.


Deron
 
You clearly have an E-28 cowl. What choke rod support do you have on the gas tank? I can see by your picture that the lip where the cowl lacing attaches is also '28 as it does not protrude forward beyond the front edge. AS Tom mentioned above, you most likely will have the hole by the left kick panel for the left brake.
 
Here are some pictures that may help. Your hole
looks like it is also to low.

Bob
 

Attachments

  • firewall.jpg
    firewall.jpg
    51.7 KB · Views: 271
  • firewall1.jpg
    firewall1.jpg
    55 KB · Views: 261
Bob C said:
Here are some pictures that may help. Your hole
looks like it is also to low.

Bob
Click to expand...

In looking at the photos posted by Bob C, the hole for the starter rod is slightly to the left of the "D" nut at the bottom of the firewall, in the photo posted by Vern Hodgson the hole for the starter rod is significantly further to the left. The hole in the Bob C photo appears to be at the same height as the photo posted by BOB C.

?????????????????????????????
 
Tom Wesenberg said:
In post #1, what is the large round hole in the motor mount on the forward side?
Click to expand...

That's one of those Canadian motor mounts, eh? :D

Seriously though, it really is one of the Canadian cast mounts.



Gary Karr said:
You clearly have an E-28 cowl. What choke rod support do you have on the gas tank? I can see by your picture that the lip where the cowl lacing attaches is also '28 as it does not protrude forward beyond the front edge. AS Tom mentioned above, you most likely will have the hole by the left kick panel for the left brake.
Click to expand...

He said it has a firewall date of 28 so I'm betting the tank has been changed. It's going to be interesting to see just how early the body really is.
 
You must log in or register to reply here.
Back
Top