Lifting a Model A

especially when it is so obvious that the proper way is to use the running boards..:eek:



(Note for those unfamiliar with sarcasm..... don't use the running boards!)



(isn't it sad that I felt compelled to put that in here?)
 
good thing you said something----I was just pushing the floor jack under the running board---whew-that was close. Instead I used the muffler like some one else said years ago
 
silversink said:
good thing you said something----I was just pushing the floor jack under the running board---whew-that was close. Instead I used the muffler like some one else said years ago
Click to expand...
Make sure that you replace the muffler bearings while you have it up.
 
Ummmm... That's gonna leave a mark.
 

Attachments

  • $_4.JPG
    $_4.JPG
    58 KB · Views: 210
I went to the linked auction expecting it to be really difficult to see the problem. It wasn't difficult.
 
All they down at the bottom of the ad is the following comment
:D:D:D

" About Us
P.J.s Auto World, Inc. has been in the collector car industry for more than 31 years and we have a great reputation. Every car we sell is inspected, serviced and detailed at no additional cost to the new owner. Your vehicle will arrive, ready to drive and enjoy."

 
silversink said:
good thing you said something----I was just pushing the floor jack under the running board---whew-that was close. Instead I used the muffler like some one else said years ago
Click to expand...

I think you took that out of context. You are supposed to put the floor jack under the muffler to hold it snug while attaching the exhaust pipe clamps. Just remember to stop before the car gets off of the ground.

Charlie Stephens
 
lifting the car on the rear arms as shown did not bend them. even though they are rolled steel the car is not heavy enough to do harm. yes i agree its the wrong place for a lifting point, another issue lifting it that way is it can slide off easier but i have seen it done before.
 
Here is a response from the seller on e-bay.

We are experienced that's why we can do it like that, our lift can stagger the arms height. A model a is super light in the back end in the first place then you use the lift arms to shift the cars center of gravity to the front of the vehicle so you have almost no weight on the rear of the car. Your the second person that's asked so I am including photos of the rear arms to let you know no rear arms were hurt in the process of lifting this Model A. I have photo as well of the car on one of our drive on lifts I will switch the ebay photos to them during the day.

- florida_auto
Click "respond" to reply through Messages, or go to your email to reply <IMG alt=" " height=4><IMG id=yui_3_13_0_ym1_1_1394025112544_2996 border=0 alt=Respond width=120 height=32>



<IMG id=yiv7510431666previewimage0 style="BORDER-LEFT-WIDTH: 0px; BORDER-RIGHT-WIDTH: 0px; BORDER-BOTTOM-WIDTH: 0px; BORDER-TOP-WIDTH: 0px; border-image: none"> <IMG id=yiv7510431666previewimage1 style="BORDER-LEFT-WIDTH: 0px; BORDER-RIGHT-WIDTH: 0px; BORDER-BOTTOM-WIDTH: 0px; BORDER-TOP-WIDTH: 0px; border-image: none"> Do these photos violate eBay policies? Let us know




From: hotslim222
To: florida_auto
Subject: Other: hotslim222 sent a message about Ford : Model A RUMBLE SEAT #161240322387
Sent Date: Mar-04-14 12:51:17 PST


Dear florida_auto,

You would think someone with the experience it "looks " like you have , would know better than to pick up a car like this by the radius rods . Good luck selling .
 
How come they stand behind their jacking process and yet the images they had on the ad prior are now removed from the auction ad?
 
You must log in or register to reply here.
Back
Top