John Deer Corn grease --- ugh
- Thread starter 30-9
- Start date
glennsanders
Senior Member
Picture please ,the grease I bought fit mine
Phil Gillespie
Well-known member
In NZ had same problem. The Corn Head Grease cartridge would not fit into my grease gun. I purchased a grease gun from John Deere when I got the grease.
I also got it to go into my steering box. And also for drive shaft universal clam shell.
No complaints about having to get another grease gun as now this one is just for the Corn Head Grease and other one with EP Grease for king pins, tie rods etc.
Phil NZ.
I also got it to go into my steering box. And also for drive shaft universal clam shell.
No complaints about having to get another grease gun as now this one is just for the Corn Head Grease and other one with EP Grease for king pins, tie rods etc.
Phil NZ.
1952henry
Well-known member
This....
https://www.deere.com/en/harvesting/corn-heads/
Refering of course to the big folded up pointy thing in front of the combine. You could easily buy an award winning woody for what the corn head would cost.
And this is the critter the grease goes into...
.https://www.lankota.com/Replacement-gearbox-for-John-Deere-40-and-90-Series-corn-heads.html
https://www.deere.com/en/harvesting/corn-heads/
Refering of course to the big folded up pointy thing in front of the combine. You could easily buy an award winning woody for what the corn head would cost.
And this is the critter the grease goes into...
.https://www.lankota.com/Replacement-gearbox-for-John-Deere-40-and-90-Series-corn-heads.html
Last edited:
RalphG
Well-known member
I've only ever seen one size of grease cartridges sold here and they all fit any of the grease guns I have. You must have a non standard grease gun if there is such a thing. You always put the end without the metal ring into the gun first down against the plunger of the gun. I don't think it is possible to put the cartridge in backwards.
Ford Freak
Well-known member
Kube
Super Moderator
I've been using this stuff for years and each cartridge has fit perfectly in a "standard" grease gunSo I buy the John Deer corn grease to use in my steering box. I follow the instructions, but low and behold the canister doesn't fit into the grease gun.
Am I crazy or shouldn't the canister (which has openings on both sides( fit in the gun?
glennpm
Well-known member
Ditto here, the cartridge is a standard size and fit my grease gun fine.
You may have tried to put the pop-top end in the gun first. The reinforcing ring at this end will NOT go into the gun. The end that has a plastic or cardboard cap on it, once removed, is the end to insert in the gun.
You may have tried to put the pop-top end in the gun first. The reinforcing ring at this end will NOT go into the gun. The end that has a plastic or cardboard cap on it, once removed, is the end to insert in the gun.
Last edited:
34pickup
Well-known member
Thanks. Now I know. Although at my age, I will probably forget..
corvette8n
Well-known member
Good to hear one has same issue.. I bought this gun at Harbor Fright so that may be the problem. I bought a cheap gun from them thinking, just filling steering box I didnt need a good gun...ho yum... you get what you pay for.
I'll go to John Deer and buy a gun w next purchase.
glennpm
Well-known member
I have two grease guns, one I've had for decades and another I bought a couple of years ago from Harbor Freight specifically to keep the JD corn head grease in.
My Harbor Freight gun took the JD cartridge with no problem. Are you sure you tried to put the capped end and not the pop-top end, into the gun first?
My Harbor Freight gun took the JD cartridge with no problem. Are you sure you tried to put the capped end and not the pop-top end, into the gun first?
Yes, I followed the directions. The tube is too large to slide in.