Hood install

1930artdeco

1930artdeco

Well-known member
So I just installed the hood in preparation for the big move up north. But I cannot seem to get it to latch. And I also noticed that the hood may be tweaked a bit. Any suggestions? I probably need to oil things up as she squeals when I open the hood.

Mike
 
If you are talking about the '57, look on the middle of the firewall near the top and you will see the latch mechanism. There is a "L"-shaped pin at the rear underside of the hood that goes into this latch. That pin can be adjusted up or down and tightened with the locknut.
 
The 57 Ford hood has multiple adjustments.

1) The hinge to hood joint can be adjusted fore and after to alter the side to side clearance between the hood and fenders. You might also check the hinges at this joint to see if there are marks from where the bolts were tightened before as a starting point.

2) The front of the hood can be adjusted up and down by moving the hinges up and down at the hinge to radiator support joint which is slotted vertically.

3) The center "L" dowel that attached to the underside rear of the hood and engages the latching mechanism can be adjusted from side to side in a slot as well as vertically with engagement of the dowl into the hood fastener and then tightening the jam nut.

4) The latching mechanism on the firewall can be adjusted vertically in mounting slots.

I think it might be best to start by closing the hood (even if it doesn't latch) to see how it aligns on either side to the fenders as well as how well it aligns to the vent cowl behind the hood. If the only problem is with the latch and the hood is aligned well to the fenders and vent cowl, then you will know where to spend your time. It might be as simple as adjusting the center hood dowel (L bolt) and/or the latching mechanism. It might also be something hanging up in the latching mechanism not allowing it to close properly over the L bolt.

Good Luck,
Dave
 
And lubricate both the hinges and latch.

You might consider removing the latch striker to align the hood properly and then work on the latch.
 
Thank you for the info. I may take the latch out align the hood and then reinstall a 59 that I have laying around.


Mike
 
Sorry, just the latch is a 59. People said that is the latch to go to instead of the 57. So I was able to grab one from a yard car.


Mike
 
I never could get the front springs on the '57 I once had to quit squeaking very long. Problem is your hinges are right in front where they are pelted with 60MPH wind and rain and snow and road salt constantly. Best you can do is try to reach down in there with lubriplate all over your fingers and plaster it all over those moving pins down there.
 
Ok, oiled everything up and it still squeakes. But, it opens a lot smoother. So, I was able to line the hood in all directions but it still sticks up to high up front. I can push down on the passenger side and it will sink down but pops right back up when I release it. Are these the bolts that I loosen to drop the front of the hood down? I took the latch off to check it and lube it and it looks fine so I will reinstall it. It seems the hood ‘L’ pin is lined up right but it just bounces off the latch fingers🤔. Or they fail to catch the bar.

Mike
 

Attachments

  • DF4FD5D2-62E3-406E-B79F-3AF5378EE4FB.jpg
    DF4FD5D2-62E3-406E-B79F-3AF5378EE4FB.jpg
    61.7 KB · Views: 31
Update; I finally got her to latch with the 59 latch. I just scootched it up a bit and it seemed to latch quite easily. The cable does need some lube though but that is for later after the move.


Thank you all,


Mike
 
And the cure I use for the squeaking hood hinges(doors too) is Fluid Film... never dries out and lubricates magnificently.
Used it on all my Fords and never squeaked again.
I had a very hipo 312 once I bought from a family... the builder had passed and he sprayed everything internally with FF before he died..... the engine was cracked open after his passing(12 years later) and all the product was there protecting everything from flash rust, etc, etc.....

I really love that stuff.
 
1930artdeco said:
Ok, oiled everything up and it still squeakes. But, it opens a lot smoother. So, I was able to line the hood in all directions but it still sticks up to high up front.

I can push down on the passenger side and it will sink down but pops right back up when I release it. Are these the bolts that I loosen to drop the front of the hood down?

Mike
Click to expand...

Sorry I didn't get back on this ... CRS ... :rolleyes:

If you are sure the hinges are adjusted correctly (excellent ILL in WSM), the hinge(s) may be sprung. Are the pivot pins in the actual hinge(s) good or loose? You may have to lower the adjustment just a tad lower to have the nose sit correctly.
 
K, I assume the hinges are original as I don't see any scrape marks. As for the springs, the hood raises easily so I am assuming they are not sprung. Not sure about the pins as I have to look at a blow out pic in the shop manual. Will check this weekend. The wagon is on hold as my Model A is now giving me fits and needs to be running for the trip north.

Mike
 
... just the latch is a 59. People said that is the latch to go to instead of the 57.
Click to expand...

... hmmph ...

First time I have heard that. I wonder what the reason is?

The reason being FORD replaced the 57/58 latch with the 59. They must have known something I don't.
 
Jeff Norwell said:
And the cure I use for the squeaking hood hinges(doors too) is Fluid Film... never dries out and lubricates magnificently.

Used it on all my Fords and never squeaked again.
Click to expand...

...hmmpf ... First learned factoid of the day ... ;)

- https://www.fluid-film.com/

1930artdeco said:
K, I assume the hinges are original as I don't see any scrape marks. As for the springs, the hood raises easily so I am assuming they are not sprung. Not sure about the pins as I have to look at a blow out pic in the shop manual. Will check this weekend.
Click to expand...

See ILL below -

The actual spring(s) slide on a sheet metal bar. That is the noise you are hearing.
 

Attachments

  • HOOD HINGE - 1957 FORD.jpg
    HOOD HINGE - 1957 FORD.jpg
    37.3 KB · Views: 23
  • HOOD HINGE ILL - 1957 FORD.jpg
    HOOD HINGE ILL - 1957 FORD.jpg
    11.3 KB · Views: 24
The 59 latches are a pretty popular swap in place of the 57-58 style, I put one on my 57 Ranchero about 10 years ago you can shut the hood with one finger instead of slamming it shut with the 57 style.
 
You must log in or register to reply here.
Back
Top