High oil pressure
- Thread starter usered
- Start date
midgetracer
Well-known member
This is about right for a B engine when cold. B engines have presurized mains. The front seal leak is a problem... probably needs a new seal. B engines tend to leak more than A engines, especially until the rings seat. Also make sure that you have the larger B type oil fill tube.
Purdy Swoft
Well-known member
A modern style front seal could be the cause of the leak. I always use the original type rope front seal, they are easier to remove and replace. If the shank of the crankshaft pulley isn't PERFECTLY smooth and round, the modern style front seal will fail quickly.
Jim Brierley
Well-known member
I think your pressure is higher than normal. The stock B's that I have run all had 3-4 lbs. cold at highway speeds and less than 1 lb. hot. Some rebuilders plug or restrict the hole at the front of the galley to gain pressure. This works but that hole is there to feed the dipper tray so you now have less oil going to the rods, not good!
usered
Senior Member
Kinda getting conflicting info on what the oil pressure should be.
Not sure it makes a lot of difference but this model B engine is not stock. Inserts, balanced crank, lighten flywheel, 3/4 cam, larger values, high compression head and dual plugs per cylinder, tube header, electronic ignition and dual 81's. See picture below.
Got a call into my builder top get his thoughts on it.
Thanks everyone
Not sure it makes a lot of difference but this model B engine is not stock. Inserts, balanced crank, lighten flywheel, 3/4 cam, larger values, high compression head and dual plugs per cylinder, tube header, electronic ignition and dual 81's. See picture below.
Got a call into my builder top get his thoughts on it.
Thanks everyone
Attachments
usered
Senior Member
Sometimes its the simplest solution! I changed the oil pressure gauge, I had an old APCO gauge I was using and I swapped it for one out of one of my other cars and now its 3-4 lbs cold and 8 - 10 hot.
I did talk with the builder and he said that he had used a rope type front seal. Its still leaking more then I would like so I still have that problem to deal with.
V4f maybe PM me I'd be interested in what you did on your pump.
I did talk with the builder and he said that he had used a rope type front seal. Its still leaking more then I would like so I still have that problem to deal with.
V4f maybe PM me I'd be interested in what you did on your pump.
Note the Model B engine that I referred to above in post #3 is stock and has the oil pressures as listed above.
This engine was stock and had standard bore, pistons, Ford valves, std sized rods and mains when I rebuilt it.
I also have seen B engines with very low oil pressure, which I think is caused by using the wrong oil pump shaft.
The low pressure is an indication of insufficient oil flow to the dipper pan and the rods through the large hole in the front of the oil galley. That is ... not enough flow to keep the dipper pan full of oil at higher engine speeds.
The A engine gets HP at 2200 and the B engine at 2800 so more oil flow is needed to keep dipper tray full of oil.
On this engine all the holes in the oil gallery are unchanged and of stock size.
It also has the correct stock Model B oil pump with the turned down shaft (.410 As I remember) as discussed in the 1932 Service bulletins page 67.
The pump in my engine does not have the 1/2 shaft that the Service Bulletins says should not be used in a Model B pump or "engine damage will result".
The "early 28" used the undercut shaft. Only use that shaft in that early pump.
Ford went back to the undercut shaft for the "B" engine. You can use the undercut shaft for any pump.
As the 1/2 " shaft is the only one made at this time, Have it turned down if you need the undercut version.
All this information is in the Service bulletin's 28 to 31 and 32 for the "B" pump.
The "Service bulletin's" make it very clear,,,, don't mix up the shafts or you will have insignificant flow !!! and as the Factory put it,,, you could damage the engine!
Copy of SB and dimensions of shaft are on Vince Falter's website:
http://www.fordgarage.com/pages/boilpumpshaft.htm
Please note that there is additional info in the SBs that is not included on Vince's website or as posted above.
Such as which sized shaft can be used in which oil pump housing (there are several housing types) and why that is true.
This engine was stock and had standard bore, pistons, Ford valves, std sized rods and mains when I rebuilt it.
I also have seen B engines with very low oil pressure, which I think is caused by using the wrong oil pump shaft.
The low pressure is an indication of insufficient oil flow to the dipper pan and the rods through the large hole in the front of the oil galley. That is ... not enough flow to keep the dipper pan full of oil at higher engine speeds.
The A engine gets HP at 2200 and the B engine at 2800 so more oil flow is needed to keep dipper tray full of oil.
On this engine all the holes in the oil gallery are unchanged and of stock size.
It also has the correct stock Model B oil pump with the turned down shaft (.410 As I remember) as discussed in the 1932 Service bulletins page 67.
The pump in my engine does not have the 1/2 shaft that the Service Bulletins says should not be used in a Model B pump or "engine damage will result".
The "early 28" used the undercut shaft. Only use that shaft in that early pump.
Ford went back to the undercut shaft for the "B" engine. You can use the undercut shaft for any pump.
As the 1/2 " shaft is the only one made at this time, Have it turned down if you need the undercut version.
All this information is in the Service bulletin's 28 to 31 and 32 for the "B" pump.
The "Service bulletin's" make it very clear,,,, don't mix up the shafts or you will have insignificant flow !!! and as the Factory put it,,, you could damage the engine!
Copy of SB and dimensions of shaft are on Vince Falter's website:
http://www.fordgarage.com/pages/boilpumpshaft.htm
Please note that there is additional info in the SBs that is not included on Vince's website or as posted above.
Such as which sized shaft can be used in which oil pump housing (there are several housing types) and why that is true.
Last edited:
Are you able to run with 50% antifreeze?
I have a similar set up with the smaller pulley. My speedster overheats with 50% antifreeze. Radiator etc is clean.
Evidently the head casting has too much space around the impeller. It has been suggested that the stock pulley would solve my issues.
Thanks for sharing your information.
I have a similar set up with the smaller pulley. My speedster overheats with 50% antifreeze. Radiator etc is clean.
Evidently the head casting has too much space around the impeller. It has been suggested that the stock pulley would solve my issues.
Thanks for sharing your information.
usered
Senior Member
I'm running 50% antifreeze with a five blade plastic fan and overflow tank. I haven't run the car to much as I'm just finishing it but to date overheating hasn't been a problem. I've got about 50 miles on it, some of it was at 65 - 70mph. I have another motor I'm running the cast iron Lion and do have some overheating issues. If you want more info PM me and we can maybe hook upon the phone.