Ford Flathead Torque Tube Identification?

Ford1941

Ford1941

Member
Could somebody possibly help me determine the correct years of application for a Ford torque tube that I have? This tube is exactly 70" long (not 70 3/4"), has no bracket for the brake hose/service brake cable, and the mount for the radius rods is near the front of the torque tube (16 - 17" from the front). Based on this information, I know it will not fit a 41 - 48 Ford, but I am not sure what years it does fit. Thanks, Scott
 

Attachments

  • IMG_0938.jpg
    IMG_0938.jpg
    19 KB · Views: 104
If no center bearing, looks like a 35-6... With center bearing, 37-40... I did not go to measure from my junk pile...
Karl
 
My torque tube does have a central bearing. Another thing it has that differes from the 41-48 torque tubes (that I am more familliar with) is a thicker-walled bearing in the front by the front seal and speedo gear. This front bearing is more solid than the "squeezable" ones that are used in the 41-48 torque tubes (and consequently, it was much more difficult to remove.

I, too, had heard this might be a 37-40 tube, but, I am surprised the the radius rods on a '40 would be located so different from the 41-48. I also thought that maybe the lack of a brake line bracket might have been linked to the lack of juice brakes prior to '39 (if my date is right). Scott
 
If I remember right, my 40 has an emergency brake bracket that attaches to the radius rod mount. 39/40 service brakes (the hydraulic bits) attach to the radius rods, not the torque tube. Other than that I have not checked the length, it looks like a 37-40 tube, with a central bearing to support the solid drive shaft.

Mart.
 
Ford1941 said:
My torque tube does have a central bearing. Another thing it has that differes from the 41-48 torque tubes (that I am more familliar with) is a thicker-walled bearing in the front by the front seal and speedo gear. This front bearing is more solid than the "squeezable" ones that are used in the 41-48 torque tubes (and consequently, it was much more difficult to remove.

I, too, had heard this might be a 37-40 tube, but, I am surprised the the radius rods on a '40 would be located so different from the 41-48. I also thought that maybe the lack of a brake line bracket might have been linked to the lack of juice brakes prior to '39 (if my date is right). Scott
Click to expand...

Radius rods for the 42-48(maybe 41) are alot shorter than the 37-40 style. I had to cut down a pair of 37 rods about 10-11 inches to fit my 32 frame, then I found a pair of 46's, and they would have fit great without cutting.
 
Some time ago, I measured a 35 - 36 torque tube: 69 15/16" long - essentially the same as your 70".
John
 
my '37 torque tube does not have a centre bearing of grease nipples from which the bearing would have been greased. It has a solid axel with the boss suggesting it should or could have a centre bearing but, the torque tube itself does not look like it had a centre bearing. Are ALL '37 passenger torque tubes equipped with a centre bearing?
 
Ford1941 said:
Could somebody possibly help me determine the correct years of application for a Ford torque tube that I have? This tube is exactly 70" long (not 70 3/4"), has no bracket for the brake hose/service brake cable, and the mount for the radius rods is near the front of the torque tube (16 - 17" from the front). Based on this information, I know it will not fit a 41 - 48 Ford, but I am not sure what years it does fit. Thanks, Scott
Click to expand...

Same length as '37-'40. '41 and later radius rods are much shorter (mount farther back on torque tube).

Coop

.
 
Ford used a barrel shaped drive shaft that was hollow like a tube in the mid 30s. They changed over to a solid shaft in the late 30s and had to add the center bearing to prevent whipping of the shaft inside there.

Wait till you find a Mercury torque tube. Those will stump a lot of Ford guys due to the extra length.
 
As I've posted prior, . . . a post now and then to inform THOSE UNAWARE of the center bearing. I've posted my experience regarding a sudden horrendous screeching upon driving my '36 half ton the first time.
The grease fitting on the top of the torque tube, not viewable. Upon realizing & using this fitting, = a drop of grease ONTO the dry ruined bearing. (fortunately, the bearing is a common hdwe store bearing.) Henry's engineers didn't engineer access INTO the bearing. . . . thank you!
 
The center bearing is lubed through a Zerk on the bottom of the torque tube, which should be very visible. The original bearing is molded into a rubber collar and today is very hard to find with very high prices ($150.+). Skip Haney has a replacement for the bearing with a much more reasonable price.

Ford1941: Somewhere about 1937 Ford used a very different size front bearing and sleeve just to the rear of the U-joint and speedo turtle, in the torque tube. It appears that is what you have. There have been several posting here on fordbarn regarding this torque tube and it's bearing.
 
You must log in or register to reply here.
Back
Top