Filter install

Gooseloony

Gooseloony

Senior Member
Have been having troubles with carb., cleaned it twice. First time car fired right up--2 days later wouldn't start; cleaned it again and installed inline filter between sediment bowl and carb, fired right up, ran for 5 minutes or so then started to starve for gas, then died. Now won't start, it has gas in the tank and the new filter appears clear. I did receive the pencil filter I ordered a few days ago, should I try installing it or is it possibly a bad carb? Any ideas and if I do install the pencil filter inside the tank, can anyone recommend a means and method (photos are very helpful). Thank you, Nick
 
Hey Nick,
Question first...have you ever had your tank cleaned/inspected for rust ?
What I'd try to see first, is if tank rust IS clogging up system. take a line (rubber hose) and run it down into a large container. Open the fuel petcock at tank and drain fuel to see what comes out. If rust , you have a decision to either clean tank thoroughly, or to install a 'dirty leg' (or whatever it's called) to catch all debris and empty it regularly until all rust particles are trapped / removed.
Do you have the brass wire filter installed up inside of tank ? This will help also, if you want some help in filtering what is coming from tank (suppliers have this scheen).
Now when you drain tank contents into a large container, you will get a good idea where you stand as far as how rusty stuff is coming from tank. An inline filter will only catch so much stuff before needing replacement.
I also place very strong large magnet beside outlet of tank, for insurance, even tho my tank has been cleaned.

Oh, and DO NOT push gas line in tooo far into carb inlet as this will create problem which will be fuel starving symptoms.
 
Last edited:
Remove the gas cap and see if the car runs. You may have the vent hole in the gas cap plugged off. 30-31 repo gas caps with a single rivet in the center are notorious for rotating the vent hole out of position and plugging it off.

Tom Endy
 
Tom I will try that (forgot to mention my car is a '28 if that matters?). And Hardtimes, thanks for explaining the process, something tells me I may have to do as you suggested. I would've thought the filter I put in would have taken care of any sediment issues to the carb.
 
I seem to remember a thread a while back about using a electric fuel pump and a large filter and chase tail (pump the gas out the bottom and back into the filler). I think it was Tom that suggested that, could be wrong.
 
I forgot to mention, if you have the glass sediment bowl, a Wix #33039 filter fits in it. I'll have to double check the number, it's a filter for a '77 Cadillac or something crazy like that.
 
I've had the filter that fits in the glass bowl clog up with very fine sediment very quickly, with the result that you describe. I just took it out and have had no problems.
 
1. evaluate the severity of the situation by looking in the tank if need be flush it
2. Get rid of your inline style filter as some of them impede the gravity flow plus they're ugly.
if you cut your line to install it buy a new one, and make sure the line does not extend more than 1/8 past the ferrules on both ends or it will restrict the flow
3. Install the pencil filter in the tank
4. install a sediment bulb filter change as necessary but if this one continues to clog the dirty leg will help. as always the best way is to restore or replace the tank.

i run the filter even though i dont have a problem with crap ,,its just good insurance


IMG_0727.jpg


9a9fbe2dfc5412ed3d981a8e288a959a_zps440aec45.jpg
 
Last edited:
What a gorgeous looking engine Mitch. I assume the exhaust manifold is ceramic. Did you paint the extension to the muffler?
 
BudP said:
What a gorgeous looking engine Mitch. I assume the exhaust manifold is ceramic. Did you paint the extension to the muffler?
Click to expand...

thanks Bud
pictured above
i high temp powder coated the manifold and entire muffler assy it has held up excellent

on lucy i used the ceramic manifold and hi temp powder coated the muffler black
this one is just completed so well see how it holds up
Mitch
 
Thank you guys. Mitch would you have any suggestions on installing the pencil filter? I'm not much of a mechanic, are there any tricks of the trade, the instruction says it just pushes in but then it says shims may be needed etc, also do the threads need any retreatment with anything while reinstalling? I'm confused, any photos would also be helpful. Thanks for everyone's help. Sorry photo came out sideways.
 

Attachments

  • gas_valve.jpg
    gas_valve.jpg
    319.6 KB · Views: 103
its been my experience of all the pencil filters i installed were a perfect fit into the valve. nothing else was needed..
i use liquid teflon on the valve threads never had a leak..
i usually put a 1/4 " fuel hose on the end of the line at the carb and drain the tank out into a gas can
keep a container handy in the car to catch any extra fuel when removing the valve or undoing the inside line
 
I guess what confuses me is that it looks like a short nipple between valve and tank, where does that filter go in at that point. Does it get pushed up into the tank and then the nipple goes in, then the valve? I'm still confused.
 
remove the valve and it installs on the threaded end. look at the other thread Tom posted on the cut away filters. that shows it pretty clear from the view inside the tank
the screen goes into the hole on this pic
 

Attachments

  • image.jpg
    image.jpg
    59.6 KB · Views: 111
Oh think I see now (gotta tell you, photos work wonders for me). Just to recap---so remove the valve, put the filter into the top of the valve and screw the valve back in? So that's not a nipple between tank and valve?
Thank you very much Mitch
 
I had a fuel problem with my A. It would run a few feet and stop. Worked on everything, then I removed the in line plastic fuel filter. That fixed it.
 
i happen to be doing one today here is a pic the filter base just needs to be pushed in a little further. its a very tight fit
 

Attachments

  • image.jpg
    image.jpg
    51.1 KB · Views: 140
You must log in or register to reply here.
Back
Top