Early vs. late

Tudie 36

Tudie 36

Senior Member
Ordered points without pulling Distributor first, guess mine was an early year after all. Is this a Norse brand rotor?
 

Attachments

  • 585D28FC-87EA-42E3-B26E-CEE00CA0F7A5.jpg
    585D28FC-87EA-42E3-B26E-CEE00CA0F7A5.jpg
    52.7 KB · Views: 533
You will need to take that dist off to do anything with it. Then even with new points, it works best when set up on a dist. machine. There is a shop, I believe on TN ave in Lonsdale, Knoxville that has a machine. You will need to ask around that area.
 
jimTN said:
You will need to take that dist off to do anything with it. Then even with new points, it works best when set up on a dist. machine. There is a shop, I believe on TN ave in Lonsdale, Knoxville that has a machine. You will need to ask around that area.
Click to expand...
490035
 
Tudie,
Box it up and send it 3RD Gen in McMinnville Tenn...Michael Driskell....
hisself will square you away. It's easy to see how this happened....early '36 used those
points and midyear '36 used that rotor. Michael has the machine/s to spin it up.
Charlie ny
 
Charlie ny said:
Tudie,:D
Box it up and send it 3RD Gen in McMinnville Tenn...Michael Driskell....
hisself will square you away. It's easy to see how this happened....early '36 used those
points and midyear '36 used that rotor. Michael has the machine/s to spin it up.
Charlie ny
Click to expand...

Thanks, I actually have the correct points and what looks like the correct rotor on order from Third Gen. They are not too far away. If I knew they did this I probably would have had it back by now, Huh? Oh well, learning as I go has been fun and I’m ready for another one. Anyone trade a couple of Harleys for a 39?
 
Charlie ny said:
Tudie,
Box it up and send it 3RD Gen in McMinnville Tenn...Michael Driskell....
hisself will square you away. It's easy to see how this happened....early '36 used those
points and midyear '36 used that rotor. Michael has the machine/s to spin it up.
Charlie ny
Click to expand...

Just off the phone with Mike @ 3rd. Gen. I do have a mixture of years. He walked me through, had me send pictures to confirm everything, I decided to buy one of his and keep mine for a spare. Great help and company from my experience and thanks again for the recommendation. I may have a leg in the door as an apprentice now.
 
Well, installed new rebuilt distributor. Started easy and sounded better. Didn’t stumble at top of shifts. Thought everything was great. Took her a little farther down the road a second time and would start loosing power under load. I think I’m good on the electrical side except to change out ignition wire. I believe it’s a venting problem or clogging filter at electric pump. Still doesn’t want to take gas. I blew compressed air into vent tube at filler neck but it’s pouring rain here in East Tennessee. Will take her out when it dries up and see if that did it. If not,I’m going to have to find somebody around Maryville Tn. To have a look see. Thanks again for all advice and commentary.
 
If all else fails bring it here to McMinnville in a couple weeks.
I appologize as I dont remember, but did you change your condenser. If you are running the adapter plate I use a FD72 Condenser.

Have you checked your primary and secondary resistance of your coil? What part# coil are you using
 
35fordtn said:
If all else fails bring it here to McMinnville in a couple weeks.
I appologize as I dont remember, but did you change your condenser. If you are running the adapter plate I use a FD72 Condenser.

Have you checked your primary and secondary resistance of your coil? What part# coil are you using
Click to expand...

The condenser was a Napa brand. It was a month old so didn’t change it. I will now. The coil only said 6 volt 505. I put on a O’Reilys to see if it changed. Still stumped. Thanks, I’ll let you know.
 
Last edited:
jimTN said:
You will need to take that dist off to do anything with it. Then even with new points, it works best when set up on a dist. machine. There is a shop, I believe on TN ave in Lonsdale, Knoxville that has a machine. You will need to ask around that area.
Click to expand...

Hello, you’re not too far from me, I got it done by Third Gen. Good, and fast work. Thanks
 
You must log in or register to reply here.
Back
Top