Dove tail rubber install

Brendan1959

Brendan1959

Member
I need some help installing the rubber and steel things in my A roadster door.
I have broken a couple of the metal bits trying to get them in. is there a trick to it?
Regards
Brendan
 

Attachments

  • A702610FS_pJPG.jpg
    A702610FS_pJPG.jpg
    8.4 KB · Views: 36
  • A47150_pJPG.jpg
    A47150_pJPG.jpg
    12.9 KB · Views: 20
Unfortunately, most of the kits for these are vintique quality. In other words, they do not fit. If you have the original metal bits, use them. The rubber usually needs to be trimmed to fit. The copper strip usually fits once the rubber has been trimmed, sometimes requiring a small bit of trimming. If you think fitting it to a roadster is bad, try a slant window sedan kit..... garbage.
 
Brendan1959 said:
I need some help installing the rubber and steel things in my A roadster door.
I have broken a couple of the metal bits trying to get them in. is there a trick to it?
Regards
Brendan
Click to expand...

Brendan,
This has been discussed previous threads. If I remember correctly, even our most experienced (roadster) members have stated that slow/careful 'trimming' of the rubber is necessary. And, that's what I did to accomplish the deed. Of course, if you can get/use original parts..you are lucky guy:) !
BTW- the 'steel' things are not steel, but brass,eh! And, I would do only a very limited 'bending' of these , as they are springy, but somewhat fragile ...at least my repros are.
 
Last edited:
Here is a pic of my 30 Phaeton door. Same as a Roadster. All parts are repro.(Sorry.)
 

Attachments

  • Img_0050.jpg
    Img_0050.jpg
    44.1 KB · Views: 120
Yes definitely upside down. I have found the set from Brattons need no trimming, rubbers slip in a little soapy and a thin blade in the back middle of the brass and a little push and they pop in. If you've ever looked at originals you'll see they are short but fat leading one to believe over 80years have compressed, the ones I have seen are not A's much hard, but gummy. If you trim they will not work as designed
 
Should look like this, i used a snap ring pliers to hold the rubber apart and get the metal piece started between the rubber.
 

Attachments

  • 16661269041683906712343218518044.jpg
    16661269041683906712343218518044.jpg
    23.1 KB · Views: 207
Dredging up an old thread.

The driver side door of my '31 CCPU is in desperate need of a new clip and rubbers. The opening has been beat up a bit too. Do these install from inside or outside the door? Has anyone made a video showing how to do it? That sure would be helpful.
 

Attachments

  • 20230304_151952_copy_567x1008.jpg
    20230304_151952_copy_567x1008.jpg
    23 KB · Views: 86
I think that damage was from a previous life. The dovetail now lines up with the center of the opening.
 
be interesting to hear from someone who has a show car. What did they do to put the parts in the door and how does it look. Bill
 
First check the brass clip fits in the opening. You hay find that you will need to file some of the sides to help it fit. Second Liquid soap on rubber helps them slid into place.
 
No one has stated it, but I assume these are installed from the outside of the opening, not from inside the door. Are there brackets of some sort above and below the opening that capture the rubbers? Thanks.
 
Hear is my 30 roadster. Works well. I ground the rubber on a belt sander to fit.



John
 

Attachments

  • 817ECD20-89B7-4EF9-92FA-73BE501E4871.jpg
    817ECD20-89B7-4EF9-92FA-73BE501E4871.jpg
    49.8 KB · Views: 71
A big help whenever fitting stubborn rubber parts, is to warm the parts, boiling hot water works good... soap also.
Joe B
 
You must log in or register to reply here.
Back
Top