Don't ask me how

TinCup

TinCup

Well-known member
Reassembling a motor that a club member brought back from New York state all went well until this piston decided to not to cooperate. The pistons are 120 over and finding replacements has turned out to be the proverbial needle in the haystack. Exhausted all of our leads here in the middle of America so reaching out to the rest of the world.

We can bore to 125 but would rather stay with the 120's if we can. Hoping somewhere in the barn is a single or a set.
 

Attachments

  • 120_Piston.jpg
    120_Piston.jpg
    41.9 KB · Views: 222
Last edited:
Judging from their style, they are really old pistons. I doubt you'll find any like them so boring or honing out to .125" (4") is probably your best bet. Good luck!
 
If you are going to the expense of boring and new pistons, maybe consider re-sleeving back to standard. Did you try Egge Machine for a new set of pistons & rings?
 
Re-sleeve it back to standard.

If it’s worth doing, it’s worth doing right. Enjoy.
 
You could have a set of .125 over pistons machined down to suit, take the block out to .125 over or sleeve it back. You have plenty of optoins. I think you were probably lucky it failed now and not out on the road somewhere in the middle of now where.
 
Synchro909 said:
You could have a set of .125 over pistons machined down to suit, take the block out to .125 over or sleeve it back. You have plenty of optoins. I think you were probably lucky it failed now and not out on the road somewhere in the middle of now where.[
Where is "NOW WHERE"? Is it somewhere past where the ROAD ENDS? That would be past where we used to live, but "maybe" Chief could fix it, he wuz GOOD!

SA Bill W./QUOTE]
Click to expand...
 
BILL WILLIAMSON said:
Synchro909 said:
You could have a set of .125 over pistons machined down to suit, take the block out to .125 over or sleeve it back. You have plenty of optoins. I think you were probably lucky it failed now and not out on the road somewhere in the middle of now where.[
Where is "NOW WHERE"? Is it somewhere past where the ROAD ENDS? That would be past where we used to live, but "maybe" Chief could fix it, he wuz GOOD!

SA Bill W./QUOTE]
Click to expand...

I have heard the outback defined as all the land that lies beyond where the wind starts., No where is the next one after that!!
Click to expand...
 
Synchro,
We've lived in West Texas where the wind & sand blow, sounds much like your "OUT-BACK"---Ever have SAND on your table & even between your bed sheets?
We lived in funky OLD HOUSES that even whistled & the linoleum on the floor, would even float up & down when the WIND blew----NLOL---My modern house is like a CASTLE, compared to that!!!
Even modern houses there, can't have insulation above the ceiling & every couple of years, SAND has to be scooped out, above the ceiling. "Somehow" the sand is able to leak into the attic area!
Once there, during a sand storm, Chief & my Uncle were trying to get home with their wagon & 2 Mules, they spooked & ran away & Chief & Uncle Pappy jumped off & walked home, as if walking in a FOG! The Mules were waiting patiently, at the corral. Sounds like an Old Western Movie--LOL
Bill W.
 
Last edited:
BILL WILLIAMSON said:
Synchro,
We've lived in West Texas where the wind & sand blow, sounds much like your "OUT-BACK"---Ever have SAND on your table & even between your bed sheets?
We lived in funky OLD HOUSES that even whistled & the linoleum on the floor, would even float up & down when the WIND blew----NLOL---My modern house is like a CASTLE, compared to that!!!
Even modern houses there, can't have insulation above the ceiling & every couple of years, SAND has to be scooped out, above the ceiling. "Somehow" the sand is able to leak into the attic area!
Once there, during a sand storm, Chief & my Uncle were trying to get home with their wagon & 2 Mules, they spooked & ran away & Chief & Uncle Pappy jumped off & walked home, as if walking in a FOG! The Mules were waiting patiently, at the corral. Sounds like an Old Western Movie--LOL
Bill W.
Click to expand...


Bill, I drove a truck for quite a few years going up and down West Texas. We usually turned off west from Hereford and then south through Donky Slipper, you know where that's at. I've been caught in some light storms and gone through when the road was over half drifted from the red sand.
 
I already posted in the wanted section and at this point the only venue I haven't tried is the telegraph. The whole point here is I don't want to have to put more money in the machine shop. Yes I could do all of the alternatives listed here but this is not that type of project.
 
BILL WILLIAMSON said:
Synchro,
We've lived in West Texas where the wind & sand blow, sounds much like your "OUT-BACK"---Ever have SAND on your table & even between your bed sheets?
We lived in funky OLD HOUSES that even whistled & the linoleum on the floor, would even float up & down when the WIND blew----NLOL---My modern house is like a CASTLE, compared to that!!!
Even modern houses there, can't have insulation above the ceiling & every couple of years, SAND has to be scooped out, above the ceiling. "Somehow" the sand is able to leak into the attic area!
Once there, during a sand storm, Chief & my Uncle were trying to get home with their wagon & 2 Mules, they spooked & ran away & Chief & Uncle Pappy jumped off & walked home, as if walking in a FOG! The Mules were waiting patiently, at the corral. Sounds like an Old Western Movie--LOL
Bill W.
Click to expand...



I like your story and I will bring it to my wife's attention. We live in a small rural town with plenty of trees around and river adjacent to the south. She, wife Patsy, complains about dust and asks where does it come from. Well after reading your situation she should be pleased with our ours. cheers, gary m
 
TinCup said:
I already posted in the wanted section and at this point the only venue I haven't tried is the telegraph. The whole point here is I don't want to have to put more money in the machine shop. Yes I could do all of the alternatives listed here but this is not that type of project.
Click to expand...

OK I guess it is time for some JB Weld!
 
During the depression sometimes a broken piston and rod were removed and the car run on 3 cylinders.
 
Last edited:
You must log in or register to reply here.
Back
Top