Anyone recognize these?

clifforddward

clifforddward

Senior Member
Does anyone recognize these two parts? I found them buried in the trunk of my recently acquired 1931 68C Cabriolet...I've searched the various books and magazines I have and cannot see anything like these parts. I did not want to miss something before casting these aside.
Thanks in advance for any info.
Best Regards,
Cliff
 

Attachments

  • 1-P1140339.jpg
    1-P1140339.jpg
    50.1 KB · Views: 387
I'm no expert...but it looks like a bracket for a drop-in removable item, such as a seat, panel or other component.
Another point to consider is it may not be a Model A part, don't throw it away, stash it away, because you never know.
 
The one in the bottom of the picture is a very nice condition stainless Dual-Rule used for imperial and metric measurement of unknown parts. :D
 
Thanks Folks...I'll just toss these in my scrap metal bin....that way I can struggle to search for them 6 months from now when I figure out what they are and need them for a project....HaHa!
 
The bottom one is a bracket to mount a toolbox on the front of 30/31 Model A. You would need 2 plus some other parts and a craftsman tool box. I used to make them from an article in the Restorer magazine 30 some odd years ago. It let you easily remove the toolbox to hand crank the car, but it could be a real knuckle buster if you weren't careful. A few are still floating around here on friends cars.
 
Agree with Colonial Coupe. I have one of the toolboxes on front also. The slot is so you can slide it back and lift the box off.
 
Find an eight inch floppy disc to give to the next owner.

Tell him it has important stuff on it.

But you don't know what it is, so don't throw it away.
 
Tool Box Bracket...half of a pair needed to install...makes sense, and yes, something I'll never use, but as I am half hoarder I'll probably never through it away from the metal bin either...

Eight inch floppy...now that is old!...size had been reduced to 5-1/4" by the time I came along...
 
Oh katy, what a youngster you are...first commonly used floppy discs were 8" units replacing tape storage in the late 60s....then reduction in size to 5-1/4" around 1976 or so....by the early 80s 3-1/2" became the norm until those "new fangled" compact discs came on the scene in the late 80s.

I suppose one would have to go to eBay or some vintage store to find an 8" reader these days...

For bonus points does anybody remember the screaming speed or storage capacity of those early 8" discs?....I'm sure any device today holds geometrically more data.
 
My first encounter with a "floppy disk" was the plastic lid to the Cisco can of cooking shortening that my Mom had in the kitchen.
We used those as flying disc's, and yes they were kind of floppy, of course this was years and years before anyone heard of a "Frisbee"

I'm not old, it's just that you are way to young
 
clifforddward said:
Oh katy, what a youngster you are...first commonly used floppy discs were 8" units replacing tape storage in the late 60s....then reduction in size to 5-1/4" around 1976 or so....by the early 80s 3-1/2" became the norm until those "new fangled" compact discs came on the scene in the late 80s.

I suppose one would have to go to eBay or some vintage store to find an 8" reader these days...

For bonus points does anybody remember the screaming speed or storage capacity of those early 8" discs?....I'm sure any device today holds geometrically more data.
Click to expand...


And compact discs have been pretty much obsoleted by USB drives. Dunno about speed (no doubt slow) but Mr Google says the first commercially available 8-inch floppy disk had a whopping 175KB capacity. I remember my first desktop with a hard drive was 20MB - thought that was so huge I'd never need anything bigger! :D


External USB drives for CD and 3.5 floppy are available.
 
Brian SATX said:
Agree with Colonial Coupe. I have one of the toolboxes on front also. The slot is so you can slide it back and lift the box off.
Click to expand...


Not questioning the purpose of the bracket but wouldn't the slotted hole allow the toolbox to slide and/or rock when the car is in motion?
 
You must log in or register to reply here.
Back
Top