Well, after a long fought battle, new dist cap, rotor, points, seat & needle, fuel pump. My brother suggested I take the vacuum suction line from the carb to the vacuum advance off at the vc end and feel if there is suction. Took it off, felt suction, started car, ran so much better. Rev'd up, no hesitation or bogging down. Could the vacuum advance need replacing? Why would the car run much better with that vacuum line off? Hopefully this is the end! Thanks.
Adjusting Float and other assorted musings
- Thread starter dgmgohl
- Start date
JSeery
Member Emeritus
Assuming it has the original 8ba distributor (loadamatic), it is vacuum advance only. A lot of distributors have mechanical advance or a combination of mechanical/vacuum advance. The loadamatic was unique in being vacuum advance only. If it is running better with the vacuum line disconnected something is wrong with the timing and/or the vacuum advance unit. Are you sure the vacuum line is connected to the correct source? It will not operate correctly if connected to manifold vacuum. The following is from VanPlets site:
Spark advance in the LoadaMatic distributor is controlled entirely by the vacuum differential at the carburetor, which regulates the vacuum control diaphragm on the distributor. The diaphragm is connected to the breaker plate and works against two springs. On 1949 Ford distributors the two springs are of separate tension. 1950 to 53 distributors have identical springs. The springs are mounted on posts with eccentric mounts. Turning the post adjusts the spring tension. Vacuum for the LoadaMatic distributor does not come from a simple vacuum fitting off the intake manifold (ie for windshield wipers), but must come from the vacuum connection on the carburetor. The stock Ford/Holley carb has the necessary two vacuum circuits internally, that are absolutely necessary for control of this distributor.
Spark advance in the LoadaMatic distributor is controlled entirely by the vacuum differential at the carburetor, which regulates the vacuum control diaphragm on the distributor. The diaphragm is connected to the breaker plate and works against two springs. On 1949 Ford distributors the two springs are of separate tension. 1950 to 53 distributors have identical springs. The springs are mounted on posts with eccentric mounts. Turning the post adjusts the spring tension. Vacuum for the LoadaMatic distributor does not come from a simple vacuum fitting off the intake manifold (ie for windshield wipers), but must come from the vacuum connection on the carburetor. The stock Ford/Holley carb has the necessary two vacuum circuits internally, that are absolutely necessary for control of this distributor.
Last edited:
scicala
Well-known member
The following is from VanPlets site:
Spark advance in the LoadaMatic distributor is controlled entirely by the vacuum differential at the carburetor, which regulates the vacuum control diaphragm on the distributor. The diaphragm is connected to the breaker plate and works against two springs. On 1949 Ford distributors the two springs are of separate tension. 1950 to 53 distributors have identical springs. The springs are mounted on posts with eccentric mounts. Turning the post adjusts the spring tension. Vacuum for the LoadaMatic distributor does not come from a simple vacuum fitting off the intake manifold (ie for windshield wipers), but must come from the vacuum connection on the carburetor. The stock Ford/Holley carb has the necessary two vacuum circuits internally, that are absolutely necessary for control of this distributor.
Need to read this and let in sink in. Very good description.
Sal
Spark advance in the LoadaMatic distributor is controlled entirely by the vacuum differential at the carburetor, which regulates the vacuum control diaphragm on the distributor. The diaphragm is connected to the breaker plate and works against two springs. On 1949 Ford distributors the two springs are of separate tension. 1950 to 53 distributors have identical springs. The springs are mounted on posts with eccentric mounts. Turning the post adjusts the spring tension. Vacuum for the LoadaMatic distributor does not come from a simple vacuum fitting off the intake manifold (ie for windshield wipers), but must come from the vacuum connection on the carburetor. The stock Ford/Holley carb has the necessary two vacuum circuits internally, that are absolutely necessary for control of this distributor.
Need to read this and let in sink in. Very good description.
Sal