31’ Victoria body to frame mount

[Dholupko]

31’ Victoria body to frame mount

My choke rod bares hard against the bottom of its firewall hole suggesting that the body is mounted too high or tipped back. A previous owner used 1/4” rubber spacers between the frame and body mounts. I’ve removed most of them but don’t seem to be getting the choke rod position to free up. I believe I’ve read that Victoria’s did not have wood block mounts. They only used the canvas strip between the body and frame. Can anyone lend suggestions as to what was used between the body and frame and how to align the two? My goal is to get my choke rod to run without interference with the hole in the firewall. It seems that I should shim up the rear of the body up to change the angle so that the firewall goes down as to relieve pressure on the choke rod.
For reference, the intake and carburetor are mounted correctly and my doors line up correctly (an indication that the body isn’t twisted).
Thanks in advance for your collective insight. Much appreciated!

 

[jw hash]

Re: 31’ Victoria body to frame mount

the original rubber pads were about 3/16". your engine might setting to high. does your front pulley line up with your crank hole. and what kind of rear engine mounts do you have.

 

[Dholupko]

Re: 31’ Victoria body to frame mount

My front pulley does line up. My rear engine mount is shown in the attached image.

Hopefully I attached it correctly.

 

[katy]

Re: 31’ Victoria body to frame mount

Sagged frame?

 

[Dholupko]

Re: 31’ Victoria body to frame mount

How would I check that?

 

[Oldbluoval]

Re: 31’ Victoria body to frame mount

With the body on checking frame is difficult.
If bare frame a string pulled tight will reveal. Like a brick mason lays brick!

 

[jw hash]

Re: 31’ Victoria body to frame mount

you have float-a motor mounts in the rear. if the rubbers are bad the engine will set to low in the rear.
Note I for one do not like float-A motor mounts for a number of reasons,

 

[Dholupko]

Re: 31’ Victoria body to frame mount

you have float-a motor mounts in the rear. if the rubbers are bad the engine will set to low in the rear.
Note I for one do not like float-A motor mounts for a number of reasons,

Okay. What would you suggest I buy and replace them with? Is there a reference dimension I can check to verify the back of the engine is too low? Say, a feature on the motor relative to the top or bottom of the frame?

 

[ModelA29]

Re: 31’ Victoria body to frame mount

Okay. What would you suggest I buy and replace them with? Is there a reference dimension I can check to verify the back of the engine is too low? Say, a feature on the motor relative to the top or bottom of the frame?

You can buy the replacement rubber from several of the suppliers.
https://www.snydersantiqueauto.com/product.htm?pid=978486&cat=41704

 

[Bigsnapper43]

Re: 31’ Victoria body to frame mount

Very evident the float a motor mounts have sagged. Ben there and done that. Also will cause bottom radiator hose to break loose from the tank.

 

[Herb Concord Ca]

Re: 31’ Victoria body to frame mount

The FAM part mounted to the engine has an "UP" side, should be able to see it marked in the square pad, check above and below, to make sure "this side is up".

 

[Bob Bidonde]

Re: 31’ Victoria body to frame mount

These sketches may help you.

 

[Dholupko]

Re: 31’ Victoria body to frame mount

This is great!!!! Thank you!

 

[Dholupko]

Re: 31’ Victoria body to frame mount

Thank you. New bushings are on order!

 

[Dholupko]

Re: 31’ Victoria body to frame mount

I will verify this when I put the new bushings in. Thank you!