30-31 Truck interior pix

Farrell In Vancouver

Well-known member
Hey all, getting around to gathering materials to finish the 131" AA Truck and I would like some interior detail shots of 82B cabs. Any good shots of wind-lacing, panels, seals, fasteners, kick panels,etc would help. Especially the door windlacing if any have shots of originals.
Thanks in advance for any help!
Cheers
 
Here are some pictures of a 1931 widebed in our club. This is an original with only a little upkeep.
 

Attachments

  • 1931 Widebed2.jpg
    1931 Widebed2.jpg
    79.1 KB · Views: 126
  • 1931 Widebed5.jpg
    1931 Widebed5.jpg
    86.6 KB · Views: 121
  • 1931 Widebed6.jpg
    1931 Widebed6.jpg
    52 KB · Views: 119
  • 1931 Widebed16.jpg
    1931 Widebed16.jpg
    58.1 KB · Views: 117
  • 1931 Widebed24.jpg
    1931 Widebed24.jpg
    87 KB · Views: 122
  • 1931 Widebed25.jpg
    1931 Widebed25.jpg
    79.1 KB · Views: 116
  • 1931 Widebed26.jpg
    1931 Widebed26.jpg
    56 KB · Views: 109
Here's a few more.
 

Attachments

  • 1931 Widebed27.jpg
    1931 Widebed27.jpg
    73.8 KB · Views: 82
  • 1931 Widebed31.jpg
    1931 Widebed31.jpg
    63.1 KB · Views: 80
  • 1931 Widebed33.jpg
    1931 Widebed33.jpg
    72.6 KB · Views: 81
  • 1931 Widebed34.jpg
    1931 Widebed34.jpg
    69.7 KB · Views: 76
  • 1931 Widebed36.jpg
    1931 Widebed36.jpg
    73.4 KB · Views: 77
Here are some pictures from a 18,000 mile tanker truck. Notice where the seam for the bottom seat cushion is located. The cardboard trim pieces are made of the same material as the inside cowl covers on cars.
 

Attachments

  • inside L & R rear copy.jpg
    inside L & R rear copy.jpg
    32.3 KB · Views: 84
  • inside Rt Ft copy.jpg
    inside Rt Ft copy.jpg
    53.5 KB · Views: 86
  • Seat and door copy.jpg
    Seat and door copy.jpg
    46.5 KB · Views: 94
Thanks gents!
This proves what Neil W was telling me about the covers on the windlacing being of the same fabric as the seat. Bill did you ever examine the door panel fasteners and take any pix?
Tom the rear seat back fasteners in the wide bed, I see were tabs and screws. Was this peculiar to the wide bed cabs or all late 31's in general. My cab has wide hooks welded to the inside curve of the rear belt rail.
 
Here is a picture that Neil Wilson posted of a 31 seat back that has the same mounting
as the one Tom posted. My late 31 steel top has the same mounting.

Bob
 

Attachments

  • seat back spring.jpg
    seat back spring.jpg
    97.1 KB · Views: 61
The first 82-B cabs had the seat back installation hardware shown in the attachments. And, some of the first 82-B cabs didn't have the wood stiffener above the seat.

The third attachment shows the two styles of hardware.
 

Attachments

  • xSeat Back Retainer Clip - upper 1c.jpg
    xSeat Back Retainer Clip - upper 1c.jpg
    61 KB · Views: 37
  • xSeat Back Retainer Clip - lower 1.jpg
    xSeat Back Retainer Clip - lower 1.jpg
    63.3 KB · Views: 37
  • 82-B - Seat Back Retainers.jpg
    82-B - Seat Back Retainers.jpg
    54.4 KB · Views: 40
Mine was like the first of Niel's pix, with two broken off that I later replaced. I thought model A's went through a lot of changes in 28! Seems the evolutions just kept going on and on.
 

Attachments

  • P9080750.JPG
    P9080750.JPG
    118.7 KB · Views: 33
Farrell:
Neil Wilson asked me to send you some high res closeups of the interior of my unrestored '31 AA (had 36,000 miles on it when I bought it 30 years ago). It still has all of the original interior with windlace, side panels, etc.

Send me a PM with your email address so I can send the photos.

Thanks,
Fred
 
Back
Top