21 stud stroker engine.

Selwyn

Selwyn

Junior Member
Hello everyone,

I was wondering if there are people here who have experience with a scat stroker kit in an 21 stud flathead v8?

What are the things I’am looking at to get this working? Any modifications to the bock itself? And is it worth it?

Thanks!
 
One challenge is getting bored large enough to fit suitable connecting rods down through. Your 21 stud bore started at 3 1/16” you need 3 3/16” bore which can be a challenge with a 21 stud block. A 37 block maybe but I have never sonic checked one of those.
Mike at H&H can supply you a kit for this I believe and will know answers on block and bore size to accommodate rods.
 
Yeah, I'm running a Scat 4"stroke crank in a 37 block with 3 3/16 pistons; 255 cu in. The Scat crank as supplied, did not fit the block, I had to widen the front and centre main bearing journals. And not all the rod journals were centred to the cylinder bores. Numerous emails back and forth to Scat, notifying them of the problem, they didn't seem to care. Hopefully in subsequent manufacture of these things, they've taken on board the issues I raised and rectified them, I dunno....If I was to do it again, I'd use a late oem Merc crank, and modify to suit; you could even achieve a 4 1/8 stroke that way.
 
On the one that was built for a 35 Coupe to run the GAR. They bored all eight cylinders pretty much out of the block to put sleeves in by leaving a step at the bottom and using epoxy to install the 3-3/16" sleeves. An original 255 Mercury 4-inch crank was modified quite a bit to get it in there and work. I bet those bottom head bolts were close. I don't know what head gasket they used. It ran the whole course with no problems. I think they used the last 81A 21-stud block type with water pump block off plates so it would look original in the 35.
 
Last edited:
Basically, if you want to retro fit a 255 crank into the 21 stud block, you'll need to perform the following operations; shorten the snout and reduce the diameter to suit those of a 21 stud crankshaft. Reduce the main bearing journals to 2.399 to suit the 21 stud block, BUT, you'll also need to widen the front and centre journals to match the width of your sample 21 stud crankshaft. 21 stud blocks have smaller dia mains but the front and centre mains are longer than the later 24 stud blocks. As the later crank runs a positive rear main seal, and the early cranks run a slinger, you'll need to modify the rear of your block to suit a rear main seal. Depending on the style of your existing rear main cap, this can be easy or more involved....Now, depending on what bore you're gonna run, you may need to grind the rod journals to the 1.999 dia and run 21A type rods, you'll need to run 81A style rod bearings, not the earlier flanged style. So there is a cost saving...Should you decide to grind to the 2" journal size, you could offset grind and achieve a 4 1/8 stroke. Or, and I don't know if the rods will clear the block, if you bore to 3 3/16, you could run 99A or 8BA rods. I've always run the 2" bearings and 21A rods, smaller dia gives a slower surface speed, which in my opinion is beneficial. Note though, that the piston speed is increased, and with the shorter overall length of the piston, it is more likely to 'rock' in the bore.
A lot of work, a lot of dollars if you're paying someone to perform the machining operations, is it worth it? you asked. Well I suppose it gives you bragging rights; 'I've got a 255 cu in 21 stud', but in my opinion, having done all this crap, is that a 221 cu in 21 stud, built with a few traditional mods, is far and away better than the bigger cube motors, on account of the rotating/reciprocating assembly being lighter, they are freer revving engines.
Would I do it again? Nah, it was an experiment, and whilst it is a fine running engine, it is nowhere near as exciting to drive compared to its predecessor.
 
You must log in or register to reply here.
Back
Top