1930 1931 Model A Ford Accessory Tool Box

I too have a home made box that fits between the front bumper supports. Two U shaped steel frames support the box and they were drilled to accept the bolts that hold the bumper braces. Tools, spare parts, oil etc. Only issue is it covers the crank hole. Looks good and I'm pleased with it.
 
The contoured box also covers the crank hole. With 7:1 compression .100 over and electronic ignition with centrifugal advance, I don't think I would want to try cranking it by hand. I've kind of gotten attached to my thumbs!
 
I read somewhere that the maker of a front sloped toolbox stopped making them due to complaints but he was willing to dispense the drawings for it should anyone wish to make their own. Are YOU that person? if so, do you still have the plans and are you willing to share them?
 
Last edited:
Ours has a square one made by a guy in CA. It would be easy to duplicate. There are lots of sources of premade metal boxes.

It also makes a good spot for the trophy that would slide off a curved one......
 

Attachments

  • tool box.jpg
    tool box.jpg
    74.7 KB · Views: 73
  • mcq show.jpg
    mcq show.jpg
    67 KB · Views: 68
town sedan said:
I read somewhere that the maker of a front sloped toolbox stopped making them due to complaints but he was willing to dispense the drawings for it should anyone wish to make their own. Are YOU that person? if so, do you still have the plans and are you willing to share them?
Click to expand...


Guten Abend,


A gentleman here in the forum rebuilt the box for me using O-tools. Maybe he'll get in touch? (I don't know if he wants to give you his address.)
 

Attachments

  • P1020764.JPG
    P1020764.JPG
    101 KB · Views: 98
My car came with one of the square boxes in front. It is for sale. I took it off because I thought it spoiled the looks of the front of the car.
 
I have the square tool box and it is loaded with stuff. This box also is a convenient seat when closed. It looks chunky, but after a while I am oblivious its there.
Purists need not reply to my post because I am not one of you!
 

Attachments

  • Front Apron Tool Box 353kb.jpg
    Front Apron Tool Box 353kb.jpg
    63.5 KB · Views: 56
  • Front Apron Tool Box 476kb.jpg
    Front Apron Tool Box 476kb.jpg
    90.8 KB · Views: 47
  • Front Apron ToolBox 420kb.jpg
    Front Apron ToolBox 420kb.jpg
    84.2 KB · Views: 40
  • Front Apron Tool Box 347kb.jpg
    Front Apron Tool Box 347kb.jpg
    65.2 KB · Views: 45
  • 190A 398kb.jpg
    190A 398kb.jpg
    103.5 KB · Views: 46
There's a guy making them that I saw in a clubs newsletter. I have it sitting in my office and told the guy he should get on the FB and advertise it but evidently he hasn't. It looks like the one first made and I will check when I get back from Wis and get his info.
 
From what I understand, the original maker of these tool boxes quit making them because he was tired of getting complaints about the fit.

It wasn't the fault of the tool box they didn't fit correctly, but because of all of the bent frame horns that occurred over the last 90 hears.

I have had mine for over ten years now, no problems but a few nicks.
548424
 

Attachments

  • IMG_0121.jpg
    IMG_0121.jpg
    85.4 KB · Views: 257
Last edited:
I bought a box version by Millard Springer. Loved it. I found a cardboard box that exactly fit in Millard's box. no rattle with all the parts I carried for our tours. I used a plastic fishing lured box for small stuff and fitted it in under the front seat. Sold it on the car. (I'm so lost without my Model A!)
 
I was the guy in Central California that made 100 of those boxes in the early 2000's. Sold them all out in less than a year. There is a fellow named Tom Nelson if Fresno Ca making the curved boxes, and they are very nice and have very good powder coating on them.
 
You must log in or register to reply here.
Back
Top